EnglishPortugueseSpanish

Request a Quote / Contact Us!

    Manufacturer

    Part Number or Numbers

    AFJ FFT EMI TEST RECEIVERS

    AFJ Instruments FFT Test Receivers

    AFJ offers the following 4 FFT Test Receivers

    Conducted Emission

    • FFT 3010 – 9kHz~30MHz

    • FFT 3030 – 9kHz~300MHz

    Radiated Emission

    FFT 3100 – 30MHz~1GHz

    FFT 3300 – 30MHz~3GHz

    FFT 3010 & FFT 3030 EMI TEST RECEIVERS FOR CONDUCTED EMISSION TESTING 

    Conducted Emissions are due to a spurious current throughout a power unit harness being introducted into the common power network.
    These conducted emissions exciting the device may affect other devices on the common power network.

    Conducted emissions may also generate unwanted radiation.

    The AFJ Instruments FFT 3010 & 3030 EMI Receivers have been especially designed for conducted emission measurement, both during EUT diagnostic development and for final compliance testing.

    AFJ Instruments FFT3030 EMI Receiver 9KHz - 300MHz

    FFT 3010 & 3030 EMI TEST RECEIVERS

    Based on a PC integrated architecture with WINDOWS 10 Embedded OS, FFT 3010 & 3030 EMI Receivers are ready to operate with advanced software for EMC testing, fitted with pre-selectors that allow excellent dynamic range and precise conducted emission measurements covering the frequency range from 9kHz to 300MHz. Remote control with an external PC is also possible.

    Optimized easy-to-use EMI measurement concept. Fitted with the internal pre-selector/ preamplifier AFJ FFT 3010 & 3030 units feature an excellent dynamic range and are, therefore, able to perform precise EMC tests. Measurements to commercial EMI International, European and Product standards, shall be carried out directly by comparing the EMI spectrum with the associated limit lines and switching on the appropriate detectors.

    MAIN FEATURES

    ◆ FFT Scan Mode
    ◆ Peak, Quasi-Peak, CISPR Average, RMS
    and CISPR RMS numerical detectors
    ◆ Automatic attenuation insertion in case of saturation condition during measurement sweep
    ◆ Precise digital overload detector to
    avoid saturation effects during analyzing function
    ◆ Correct pulse weighting to CISPR 16-1-1
    from PRF of 1Hz
    ◆ High measurement speed and fast detection of critical frequencies (dwell time down to 1msec)
    ◆ High sensitivity
    ◆ Large-signal immunity
    ◆ Low measurement uncertainty
    ◆ High measurement speed
    ◆ Correction values for cables loss, attenuator/amplifier, coupling networks, GTEM correction and
    antenna factors
    ◆ Integrated signal generator
    ◆ 10MHz External reference frequency
    ◆ Software option for AM / FM / WBFM
    digital demodulations

     

    CISPR 16-1-1 COMPLIANCE

    FFT 3010 & 3030 EMI Receivers fully comply with CISPR 16-1-1. The response of Quasi-Peak Detector in terms of both absolute calibration and relative calibration lays between the tolerances of CISPR 16-1-1. The pulse weighting conformity meets down to the minimum value of the Pulse Repetition Frequency (PRF) coming from the DUT, of 1Hz.

    The FFT Scan Mode is compliant to CISPR 16-3.

     

    Accuracy and reproducibility are key parameters for AFJ FFT 3010 & 3030 EMI Receiver application.

     

    Associated Downloads

    AFJ FFT 3010 & 3030 EMI Receivers Data Sheet

     

    FFT 3100 & FFT 3300 EMI TEST RECEIVERS FOR RADIATED EMISSION TESTING

    The AFJ Instruments FFT 3100 and FFT 3300 are High accuracy CISPR 16-1-1 EMI receivers for radiated emission measurements.

    AFJ also offers high precision calibrated antennas to work with the EMI Receivers.

    The AFJ FFT 3100 and FFT 3300 EMI Receivers were especially designed for radiated emission measurement, both during EUT diagnostic development and final compliance tests. They can be used in either semi anechoic chambers or OATS testing enviroments. A complete set of calibrated antennas is available up to 40GHz.

    AFJ FFT 3010 EMI Reciever Front

    Fully digital IF EMI Receivers for measurement of radiated electromagnetic interference from 30MHz to 3GHz.

    Compact designed and manufactured compliant to CISPR 16 International Standard, using FFT Scan Mode for fast measurements of radiated electromagnetic interference in accordance with requirements of EMI International, European and Product standards, pre-selectors and advanced software for EMC testing.

    Based on a PC integrated architecture with WINDOWS 10 Embedded OS, FFT 3100 & 3300 EMI Receivers are ready to operate with advanced software for EMC testing, fitted with pre-selectors that allow excellent dynamic range and precise conducted emission measurements covering the frequency range from 30MHz to 3GHz. Remote control with an external PC is also possible.

    MAIN FEATURES
    ◆ Compact unit designed and manufactured compliant to CISPR 16-1-1
    ◆ FFT Scan Mode compliant to CISPR 16-3
    ◆ Peak, Quasi-Peak, CISPR Average, RMS and CISPR RMS Detectors
    ◆ Pre-selectors
    ◆ Tracking Generator
    ◆ Advanced software for EMC testing
    ◆ Critical frequencies fast detection by through overview measurement
    ◆ 1Hz PRF CISPR 16-1-1 calibrated pulse weighting

     

    Associated Downloads

    AFJ Instruments FFT 3100 & FFT 3300 EMI Test Receivers for Radiated Emissions Test Receivers Data Sheet