EnglishPortugueseSpanish
Schlöder Product List

Schlöder- ESD Simulators
• SESD 216 ESD Simulator 16,5 KV
• SESD 230 ESD Simulator 30 kV
• SESD 30000 EDS Simulator 30 kV
• SEDS 2910 ESD – Test System 30 KV
Schlöder- EMC Generators / Measurement System
• CDG 7000 Conducted Disturbances Test System
• CWG 1500 Surge / Hybrid Generators
• CWG 2500 Surge / Combination Wave Generators
• MGA 1033 Magnetic Field Generator And Analizer
• CAL 1250 Magnetic Field Calibrator
• PG 01-2000 Pulse Generator
• PGA 1240 Immunity DC – 300 kHz
• PGA 1240-5A & PGA 1240-16A Power DC Generators
• PGA – 1330 Immunity Generator
Schlöder- Burst Generators
• SFT 1400 Burst Generator 125 KHZ
• SFT 1420 Burst Generator 2 MHZ
• SFT 2400 EFT/Burst Generator 2 MHZ
• SFT 2420 EFT/Burst Generator 2 MHZ
• VIS 1700 Voltage Interruption Simulator
Schlöder- CDN – Coupling Decoupling Networks
Schlöder- Coupling Networks For Burst & Surge
-CN 1240-32 And CN 1240-125 Coupling Switchable Networks
-Mains Operation 3-Phase
• CWG 520
• CWG 523 / CWG 523-550
• CWG 524 CWG 524-550
• CWG 524-B / CWG 524-B-550
Interconnection Lines / Surge test only
• CWG 1525
• CWG 1526
• CWG 1528
Schlöder Current Monitoring Probes
• CDG CMP-45 Current Monitoring Probe
• CDG CMP-46 Current Monitoring Probe
• CDG A CMP-46 Calibration Set for the CDG CMP-46 Current Monitoring Probe
Schlöder- Accessories
-Burst Generator Accessories
• CWG 520 – 3-phase coupling network, 4 x 16 A – Burst and Surge
• CWG 523, CWG 523-550, CWG 524 CWG 524–550 – 3-phase Coupling Network, 4 x 32 / 60 A – Burst and Surge
• CWG 524-B – 3-phase Coupling Network, 4 x 60 A – Burst only
• EMV-SOFT – Remote control software for SFT, CWG, VIS
• SFT 415 – Capacitive Coupling Clamp (CCC)
• SFT 415-1 – Capacitive Coupling Clamp with protection cover
• SFT 415-CS – Calibration Set for verification the CCC
• SFT 430 HV Cable for Burst Generator
• SFT 450-Set – Attenuator Set
• SFT 470 – Probe set for Burst generator to create short time magnetic fields
ESD Simulator Accessories
• SESD 271 – Vertical Coupling Plate
• SESD 272 – Earth Cable
• SESD 30 S 120 – ESD Remote Control Software
• SESD 30 T 1000 – Support Arm with Balancer
• SESD 3020 – SESD 3027 – Test Tip´s for ESD
• SESD 3036 – Hook for Balancer
• SESD 8800-4 – ESD Target 4GHz
Surge / Hybrid Generator Accessories
• CWG 520, CWG 520 / 550 – 3-Phase Coupling network
• CWG 523, CWG 523-550, CWG 524, CWG 524-550- Coupling networks for Burst and Surge testing
• CWG 550 – External 18 µF capacitor in a housing
• CWG 553 – External 0,5 µF capacitor + 40 Ohm resistor in housing
• CWG 554 – External 9 µF + 10 Ohm resistor in housing
• CWG 1525 – CDN for 2 unshielded, balanced signal lines, 1 A, with gas discharger arrester
• CWG 1526-4, CWG 1526-10 – CDN for 2 unshielded, unbalanced data – and signal lines, 4 A or 10 A
• CWG 1528 – CDN for 4 unshielded, unbalanced data – and signal lines, 6 A, with RS 232 interface
• EMV-SOFT – Control software for SFT, CWG and VIS generators
Immunity, 10 kHz – 230 MHz Accessories
• CDN xxx -Coupling/Decoupling
• CDG A 31xx – Calibration adapters for CDN’s
• CDN-EMCL-20 & CDN EMCL-35 – EM Clamps
• CDN ABCL-20 – Decoupling Clamp
• CDN EMCL-NW_10 – Matching Network
• BCI-P1 – Clamp Bulk Current Injection (BCI) with Calibration Set
• CDG CMP-45 – Current Monitoring Probe With Calibration Set
• CDG CMP-46 – Current Monitoring Probe
• CDG A CMP-46 – Calibration Set
• CDG 6050 – 6dB Attenuator, 20W
• CDG 6050-100W – 6dB Attenuator, 100
Immunity, DC – 150 KHZ Accessories
• CN xxx - Coupling Networks
• CN 1240 xx - Coupling networks, switchable
Magnetic Field Generator Accessories
• CMGA_HCST - Helmholtz Coils
• MGA_LS/RL - Loop Sensor
• MGA_Bx - Test adapter, EN 55103
Voltage Interruption Simulator Accessories
• VIS 740 Step Transformer
• EMV-SOFT - Control software for SFT, CWG and VIS generators
Schlöder- Helmholtz Coils
Schlöder- Signal Generator SG 0282
Schlöder- Isolation – Transformers With Double Shield Winding
Schlöder Power Frequency Magnetic Field Immunity Tests
• Schlöder MGA_BC-500 Field Coil acc. to EN 55103-2
• Schlöder MGA 1030 Magnetic Field System Data Sheet
• Schlöder MGA 1030 Magnetic Field Generator and Analyzer Additional Equipment Data Sheet
Products By Standars

Company Overview
Data Sheets
Product List

Request a Quote / Contact Us!

Manufacturer

Part Number or Numbers

CWG 2500 Surge / Combination Wave Generators

Schlöder CWG 2500 Surge / Combined Wave Generator
Schlöder SFT 2400 EFT/ Burst Generator

  • • Operation via capacitive color touch display
    • Combined wave surge voltage 1,2 / 50 µs and current 8 / 20 µs
    • Amplitude 0,2 – 4,4 kV and 0,1 – 2,2 kA
    • USB, optional optic interface with fiber optic cable

The test generator CWG 2500 simulates high-energy interference pulses and is suitable for performing EMC tests on systems in accordance with the standards IEC / EN 61000-4-5, 2014 and VDE 0847 4-5. The CWG 2500 is a combined surge current / surge voltage generator that generates a standard open circuit surge voltage of 1.2 / 50 μs and a standard short-circuit surge current of 8/20 μs. The values for current and voltage are shown on the display, for evaluations with an oscilloscope BNC outputs for current and voltage are available on the rear.
With the built-in single-phase coupling network, the interference pulses of the hybrid generator can be coupled to the supply lines of the devices to be tested. The coupling takes place by means of discrete coupling capacitors. According to IEC 61000-4-5, 18 μF capacitors (balanced coupling) or 9 μF / 10 Ω (unbalanced coupling) are installed with sufficient dielectric strength. External coupling networks can also be operated via the HV socket or used for component testing.
The simple operation takes place via a capacitive color touch display. All parameters are clearly displayed without nested menus and can be changed quickly by tapping and using a digital rotary encoder. The normative test leve

 

Front time Tr µs

Duration Td µs

Open-circuit voltage

Tf = 1,67 x T = 1,2 ± 30 %

Td = Tw = 50 ± 20 %

Short-circuit current

Tf = 1,25 x Tr = 8 ± 20 %

Td = 1,18 x Tw = 20 ± 20 %

 

Technical specifications

Generator
Charging voltage 0,2 – 4,4 kV
Charging timet ≤ 10 sec
Number of pulses 1 – 999
Repetition rate 10 – 990 sec
Phase angle ϕ = 0° – 359°, 1° steps, mains-synchronized
Polarity positive, negative, alternating
Trigger manually or externally
HV output ungrounded and ground referred
Interface USB (virtual COM Port) Optional: optical with fiber optics
Memory function Select test levels 1 – 4 (Standard), 32 memory positions
Discharge parameters Display of discharge Surge Voltage / Surge Current after discharge

 

Coupling / Decoupling Network
1-Phase, inside generator for coupling on the power supply lines of the EUT
Nominal voltage AC max. 230V / 16A, 50 / 60 Hz
Nominal voltage DC max. 270V / 16A
Balanced coupling L – N: 18 µF
Unbalanced coupling L – PE, N – PE: 9 µF + 10Ω
Phase indication LED red / green
EUT connection Schuko (protection earth) outlet + laboratory sockets
Ground connection Ground jack at front and rear panel

 

General
Operating temperature 0 – 40 ° C
Dimensions 19″ housing, 3 U
Weight approx. 18 kg
Supply voltage 100-240V / 47-63 Hz / 100 VA

Accessories
• 3-Ph. Coupling network 4 x 16 A, Burst + Surge CWG 520
• 3-Ph. Coupling network 4 x 32 A, Burst + Surge CWG 523
• 3-Ph. Coupling network 4 x 60 A, Burst + Surge CWG 524
• 3-Ph. Coupling network 4 x 60 A, Burst CWG 524-B
• Attenuator 100:1 / 50 Ohm SFT 450
• Probe set, magnetic field SFT 470
• Capacitive coupling clamp SFT 415
• Capacitive coupling clamp with protection cover SFT 415-1
• HV-Cable for capacitive coupling clamp SFT 430
• Calibration set for coupling clamp SFT 415-CS
• 50 Ω attenuator SFT 450-1
• 1000 Ω attenuator SFT 450-2
• 50 Ω + 1000 Ω attenuator set SFT 450-Set
• Optical interface with 10m fiber optic cable OPT_I_2
• Control Software for Burst / Surge / VIS EMV-SOFT

 

Aaronia_AG_BicoLOG_5070_Biconical_Antenna_Data_Sheet Schlöder CWG 2500 Surge / Combination Wave Generator Data Sheet