DANA SRL Power Supplies
Dana Linear Amplifier
• Linear Amplifier - DLA SERIES
Dana Elecrtronic Loads
• Linear Electronic Loads – DSO Series
• Linear Electronic Loads 0 Volt – DSOT Series
Dana Linear Electronic Switches
• Electronic Switches
Dana Linear Generators for Rail and Trams
• Linear Generators
Dana Digital Interfaces
• Digital Interfaces
Dana Continuous Current Generators
• Linear Continuous Current Generators – DAC Series
Dana Double Regulation Continuous
• Double Regulation Continuous Current Generators – DOC Series
Dana Power Sources
• AC/DC Power Sources – MPS Series
Dana Linear Power Supplies
• Linear Power Supplies
• Linear AC/DC Power Supplies – DA Series
• Linear AC/DC Power Supplies for Photo-voltaic Inverter Testing
• Linear 1000 Vdc Linear Power Supply – DAX-1000• Linear AC/DC Bipolar 2 Quadrant Power Supplies – D2A Series
• Linear AC/DC Bipolar 4 Quadrant Power Supplies – D4A & D4AA Series
• Linear AC/DC Multi Output Power Supplies – DP Series
• Linear AC/DC Bipolar 2 Opposite Quadrant Power Supplies – D2AC Series
• Linear Power Supply for Superconducting Coils
• Start Engine Power Supplies – DAS Series
Dana Double Regulation Power Supplies
• Double Regulation Power Supplies – DO Series
• Double Regulation 2 Quadrant Power Supplies – D2O Series
• Double Regulation Bipolar Opposite 2 Quadrant Power Supplies – D2OC Series
Dana Thystor Regulation Supplies
• Thyristors Regulation AC/DC Power Supplies – DE Series
RELIANT EMC PRODUCT LINES
MANUFACTURERS
Request a Quote / Contact Us!
DANA- Current Generators
DOC Series
Overview
With same project philosophy of “DO” series Power Supply, without changing front side look and programming commands, DANA added to our catalog this family of Current Generators. Rise and fall rate of output current are among most interesting features of this equipment providing same characteristics of a first class power supply.
Technical Features
Mains Input
115 or 230 or 400 Vac ± 10% 50-60 Hz
Line regulation
better than 50 ppm of output V max for the allowed input variation
Voltage and Current Output
adjustable, by a 10 turns potentiometer from “0” to max rated
Load regulation for constant V
from no load to full load better than 50 ppm
Load regulation for constant I
better than 50 ppm of I max from “0” to V max .
Ripple and noise
better than 50 ppm (rms) each 1.000 W
Remote programming and feed-back (GPAC)
Opto-insulated analog signal 0-10Vdc
Linearity better than 0.3% Drift better than 1.5mV/°C
Reaction to remote programming (slew rate)
2A / µs
Stability
After 20 minutes of preheating, better than 0.1% for 24 hours at 25°C ambient
Temperature coefficient
under 50 ppm/°C in “voltage mode”;
under 50 ppm/°C in “current mode”
Ambient temperature
work 0÷40°C
storage -10÷50°C
Cooling
forced air
DOC Series Double Regulation Continuous Current Generator Front Panel
FRONT PANEL CONTROLS
Power
Breaker switching equipment ON and OFF
DC
Commands allowing to hold power supply in stand-by and to make it supply according to need while a LED shows selected function
P – slider switch enabling DC output in permanent mode
(up to output voltage of 60 Vdc)
S – push-button to be used to avoid “DC” output when Power switch is on
Check
V – A – OVP set up push-buttons when the Power Supply is in stand-by
OVP (Over Voltage Protection)
trimmer allowing to set up “hazard-limit” for the EUT, when picked it up inhibits Power Supply with an alarm LED lighting up
OT
Alarm for over temperature of power circuit putting Power
Supply in stand- by with an alarm LED lighting up
Local/Remote
V/A – slide switches to select voltage and current programming mode through the front panel potentiometers (Local) or a remote command between 0÷10 Vdc through the GPAC connector or GPIB/RS interface (option)
DC – slide switch to program the DC supply from the panel control (Local) or from a remote command through the GPAC or GPIB
GPAC/GPIB
Slide switches enabling the power supply to be programmed by an analog voltage (0÷10 Vdc) through the GPAC connector on the back or through an IEEE488 – RS232/485 interface (optional)
Section V
Potentiometer and display (with accuracy of 1.5%) showing output voltage or, by means of Check button, programmed voltage.
LED of “voltage mode”
Inhibit
Alarm LED with output inhibition showing the absence of one phase in models with 3-phase mains input or available for an alarm of a parameter chosen by the customer
Section A
Potentiometer and display (with accuracy of 1.5%) showing output current or, by means of Check button, programmed current.
LED of “current mode”
GND GroundPlug
+/- Auxiliary plug to be used as test point up to 5 A max
BACK PANELS CONTROL
Remote Sense
Terminal block allowing to switch “remote sense” circuit control from power output plugs to remote sense, to recover a max voltage drop of 0,5 V for cable
GPAC
“General Purpose Analog Control” connector to program remotely the Power Supply with 0÷10
Vdc analog optically isolated voltage for all functions, to read
Voltage and Current proportional feed-back (0÷10 Vdc) and to enable “DC” output through a logic signal (0 – 5V)
+/-
Power output
OPTIONS
PS
interface to program the Power Supply with standard IEEE488/RS232
PW
interface to program the Power Supply with standard IEEE488/RS485
T
reaction to remote programming up to 8 A/µs
Y
3-phase mains input, in models with output power less than 2400 W
DOC Series Double Regulation Continuous Current Generators Model Chart
The models in the table are available with voltage and output current on customer request.
N.B. * These models are not in standard dimensions
ORDER EXAMPLE