DANA SRL Power Supplies

Dana Linear Amplifier
• Linear Amplifier - DLA SERIES
Dana Elecrtronic Loads
• Linear Electronic Loads – DSO Series
• Linear Electronic Loads 0 Volt – DSOT Series
Dana Linear Electronic Switches
• Electronic Switches
Dana Linear Generators for Rail and Trams
• Linear Generators
Dana Digital Interfaces
• Digital Interfaces
Dana Continuous Current Generators
• Linear Continuous Current Generators – DAC Series
Dana Double Regulation Continuous
• Double Regulation Continuous Current Generators – DOC Series
Dana Power Sources
• AC/DC Power Sources – MPS Series
Dana Linear Power Supplies
• Linear Power Supplies
• Linear AC/DC Power Supplies – DA Series
• Linear AC/DC Power Supplies for Photo-voltaic Inverter Testing
• Linear 1000 Vdc Linear Power Supply – DAX-1000• Linear AC/DC Bipolar 2 Quadrant Power Supplies – D2A Series
• Linear AC/DC Bipolar 4 Quadrant Power Supplies – D4A & D4AA Series
• Linear AC/DC Multi Output Power Supplies – DP Series
• Linear AC/DC Bipolar 2 Opposite Quadrant Power Supplies – D2AC Series
• Linear Power Supply for Superconducting Coils
• Start Engine Power Supplies – DAS Series
Dana Double Regulation Power Supplies
• Double Regulation Power Supplies – DO Series
• Double Regulation 2 Quadrant Power Supplies – D2O Series
• Double Regulation Bipolar Opposite 2 Quadrant Power Supplies – D2OC Series
Dana Thystor Regulation Supplies
• Thyristors Regulation AC/DC Power Supplies – DE Series

DANA Company Overview
DANA Data Sheets
Dana SRL Catalog

Request a Quote / Contact Us!


    Part Number or Numbers

    DANA-Linear Continuous Current Generators - DAC Series

    DAC Series


    Mains Input
    115 or 230 or 400 Vac ± 10% 50-60 Hz

    Line regulation
    better than 50 ppm of output V max for the allowed input variation

    Voltage and Current Output
    adjustable, by a 10 turns potentiometer from “0” to max rated

    Load regulation for constant V
    from no load to full load better than 50 ppm

    Load regulation for constant I
    better than 50 ppm of I max from “0” to V max .

    Ripple and noise
    better than 30 ppm (rms) each 1.000 W

    Remote programming and feed-back (GPAC)
    Opto-insulated analog signal 0÷10Vdc
    Linearity better than 0.3% Drift better than 1.5mV/°C

    Reaction to remote programming (slew rate)
    2A / µs (8A / µs con opzione T)

    After 20 minutes of preheating, better than 0,1% for 24 hours at 25°C ambient

    Temperature coefficient
    lower 50 ppm/°C in “voltage mode”;
    lower 50 ppm/°C in “current mode”

    Ambient temperature
    work 0÷40°C
    storage -10÷50°C

    forced air

    DANA DAC Series Linear Continuous Current Generator Front Panel
    DANA DAC Series Linear Continuous Current Generator Front Panel

    With same project philosophy of “DA” series Power Supply, without changing front side look and programming commands, we added to our catalog this family of Current Generators. Rise and fall rate of output current are among most interesting features of this equipment affording same characteristics of a first class Power Supply.


    Breaker switching equipment ON and OFF

    Commands allowing to hold power supply in stand-by and to make it supply according to need while a LED shows selected function
    P – slider switch enabling DC output in permanent mode
    (up to output voltage of 60 Vdc)
    S – push-button to be used to avoid “DC” output when
    Power switch is on

    V – A – OVP set up push-buttons when the Power Supply is in stand-by

    OVP (Over Voltage Protection)
    trimmer allowing to set up “hazard-limit” for the EUT, when picked it up inhibits Power Supply with an alarm LED lighting up

    Alarm for over temperature of power circuit putting Power Supply in stand- by with an alarm LED lighting up

    V/A – slide switches to select voltage and current programming mode through the front panel potentiometers (Local) or a remote command between 0÷10 Vdc through the GPAC connector or GPIB/RS interface (option)
    DC – slide switch to program the DC supply from the panel control (Local) or from a remote command through the GPAC or GPIB

    Slide switches enabling the power supply to be programmed by an analog voltage (0÷10 Vdc) through the GPAC connector on the back or through an IEEE488 – RS232/485 interface (optional)

    Section V
    Potentiometer and display (with accuracy of 1.5%) showing output voltage or, by means of Check button, programmed voltage.
    LED of “voltage mode”

    Inhibit Alarm LED with output inhibition showing the absence of one phase in models with 3-phase mains input or available for an alarm of a parameter chosen by the customer
    Section A
    Potentiometer and display (with accuracy of 1.5%) showing output current or, by means of Check button, programmed current.
    LED of “current mode”


    GND GroundPlug

    +/- Auxiliary plug to be used as test point up to 5 A max



    Remote Sense
    Terminal block allowing to switch “remote sense” circuit control from power output plugs to remote sense, to recover a max voltage drop of 0,5 V for cable

    “General Purpose Analog Control” connector to program remotely the Power Supply with 0÷10
    Vdc analog optically isolated voltage for all functions, to read
    Voltage and Current proportional feed-back (0÷10 Vdc)
    and to enable “DC” output through a logic signal (0 – 5V)
    Power output


    interface to program the Power Supply with standard IEEE488/RS232

    interface to program the Power Supply with standard IEEE488/RS485

    reaction to remote programming up to 8 A/µs

    3-phase mains input, in models with output power less than 2400 W


    The models in the table are available with voltage and output current on customer request.
    N.B. * These models are not in standard dimensions
    DANA DAC Series Linear Continuous Current Generator Model Options Chart
    DANA DAC Series Linear Continuous Current Generator Model Options Chart

    Order Example

    DANA DAC Series Linear Continuous Current Generator Order Example

    the DAC Series comes standard with a 3 year Warranty!