EnglishPortugueseSpanish
Schlöder Product List

Schlöder- ESD Simulators
• SESD 216 ESD Simulator 16,5 KV
• SESD 230 ESD Simulator 30 kV
• SESD 30000 EDS Simulator 30 kV
• SEDS 2910 ESD – Test System 30 KV
Schlöder- EMC Generators / Measurement System
• CDG 7000 Conducted Disturbances Test System
• CWG 1500 Surge / Hybrid Generators
• CWG 2500 Surge / Combination Wave Generators
• MGA 1033 Magnetic Field Generator And Analizer
• CAL 1250 Magnetic Field Calibrator
• PG 01-2000 Pulse Generator
• PGA 1240 Immunity DC – 300 kHz
• PGA 1240-5A & PGA 1240-16A Power DC Generators
• PGA – 1330 Immunity Generator
Schlöder- Burst Generators
• SFT 1400 Burst Generator 125 KHZ
• SFT 1420 Burst Generator 2 MHZ
• SFT 2400 EFT/Burst Generator 2 MHZ
• SFT 2420 EFT/Burst Generator 2 MHZ
• VIS 1700 Voltage Interruption Simulator
Schlöder- CDN – Coupling Decoupling Networks
Schlöder- Coupling Networks For Burst & Surge
-CN 1240-32 And CN 1240-125 Coupling Switchable Networks
-Mains Operation 3-Phase
• CWG 520
• CWG 523 / CWG 523-550
• CWG 524 CWG 524-550
• CWG 524-B / CWG 524-B-550
Interconnection Lines / Surge test only
• CWG 1525
• CWG 1526
• CWG 1528
Schlöder Current Monitoring Probes
• CDG CMP-45 Current Monitoring Probe
• CDG CMP-46 Current Monitoring Probe
• CDG A CMP-46 Calibration Set for the CDG CMP-46 Current Monitoring Probe
Schlöder- Accessories
-Burst Generator Accessories
• CWG 520 – 3-phase coupling network, 4 x 16 A – Burst and Surge
• CWG 523, CWG 523-550, CWG 524 CWG 524–550 – 3-phase Coupling Network, 4 x 32 / 60 A – Burst and Surge
• CWG 524-B – 3-phase Coupling Network, 4 x 60 A – Burst only
• EMV-SOFT – Remote control software for SFT, CWG, VIS
• SFT 415 – Capacitive Coupling Clamp (CCC)
• SFT 415-1 – Capacitive Coupling Clamp with protection cover
• SFT 415-CS – Calibration Set for verification the CCC
• SFT 430 HV Cable for Burst Generator
• SFT 450-Set – Attenuator Set
• SFT 470 – Probe set for Burst generator to create short time magnetic fields
ESD Simulator Accessories
• SESD 271 – Vertical Coupling Plate
• SESD 272 – Earth Cable
• SESD 30 S 120 – ESD Remote Control Software
• SESD 30 T 1000 – Support Arm with Balancer
• SESD 3020 – SESD 3027 – Test Tip´s for ESD
• SESD 3036 – Hook for Balancer
• SESD 8800-4 – ESD Target 4GHz
Surge / Hybrid Generator Accessories
• CWG 520, CWG 520 / 550 – 3-Phase Coupling network
• CWG 523, CWG 523-550, CWG 524, CWG 524-550- Coupling networks for Burst and Surge testing
• CWG 550 – External 18 µF capacitor in a housing
• CWG 553 – External 0,5 µF capacitor + 40 Ohm resistor in housing
• CWG 554 – External 9 µF + 10 Ohm resistor in housing
• CWG 1525 – CDN for 2 unshielded, balanced signal lines, 1 A, with gas discharger arrester
• CWG 1526-4, CWG 1526-10 – CDN for 2 unshielded, unbalanced data – and signal lines, 4 A or 10 A
• CWG 1528 – CDN for 4 unshielded, unbalanced data – and signal lines, 6 A, with RS 232 interface
• EMV-SOFT – Control software for SFT, CWG and VIS generators
Immunity, 10 kHz – 230 MHz Accessories
• CDN xxx -Coupling/Decoupling
• CDG A 31xx – Calibration adapters for CDN’s
• CDN-EMCL-20 & CDN EMCL-35 – EM Clamps
• CDN ABCL-20 – Decoupling Clamp
• CDN EMCL-NW_10 – Matching Network
• BCI-P1 – Clamp Bulk Current Injection (BCI) with Calibration Set
• CDG CMP-45 – Current Monitoring Probe With Calibration Set
• CDG CMP-46 – Current Monitoring Probe
• CDG A CMP-46 – Calibration Set
• CDG 6050 – 6dB Attenuator, 20W
• CDG 6050-100W – 6dB Attenuator, 100
Immunity, DC – 150 KHZ Accessories
• CN xxx - Coupling Networks
• CN 1240 xx - Coupling networks, switchable
Magnetic Field Generator Accessories
• CMGA_HCST - Helmholtz Coils
• MGA_LS/RL - Loop Sensor
• MGA_Bx - Test adapter, EN 55103
Voltage Interruption Simulator Accessories
• VIS 740 Step Transformer
• EMV-SOFT - Control software for SFT, CWG and VIS generators
Schlöder- Helmholtz Coils
Schlöder- Signal Generator SG 0282
Schlöder- Isolation – Transformers With Double Shield Winding
Schlöder Power Frequency Magnetic Field Immunity Tests
• Schlöder MGA_BC-500 Field Coil acc. to EN 55103-2
• Schlöder MGA 1030 Magnetic Field System Data Sheet
• Schlöder MGA 1030 Magnetic Field Generator and Analyzer Additional Equipment Data Sheet
Products By Standars

Company Overview
Data Sheets
Product List

Request a Quote / Contact Us!

Manufacturer

Part Number or Numbers

MGA 1033 Magnetic Field System DC 250 KHZ

Schlöder MGA 1033 Magnetic Field System DC 250kHz
for EN 55103-1 + 2, EN 61000-4-8, Automotive, MIL-STD and others

Schlöder MGA 103e Magnetic Field System DC 250kHz
The compact magnetic field generator and analyzer MGA 1033 allows susceptibility tests against magnetic fields from DC up to 250 kHz according the standard EN 55103-2 (product standard for professional audio, video and light control techniques) and there measurement according to EN 55103-1.

 

In combination with our tri axial Helmholtz coils full automated susceptibility tests are possible at magnetic field strength up to 1000 A/m for frequencies from DC to 1 kHz. Lower field strength can be generated for frequencies up to 250 kHz. Due to the tri axial set-up of our Helmholtz coil major improvement in device handling is achieved because there is no need to turn an EUT during tests.

 

The MGA 1033 complies to all magnetic field requirements of relevant EMC and military standards.

 

More EMC tests are possible according the standards below:

– IEC / EN 61000-4-8

– SAE J 1113-2, SAE J 1113-22

– GM W 3097

– ISO 11452-8

– Ford ES-XW7T-1A278-AC

– MIL-STD-461 E/F RS 101, CS101

– PSA B21 7110 – DC – 11224, DC 1014

– and similar standards

 

Furthermore magnetic field measurements acc. MIL-STD-461 E/F RE101, CE101 are possible.

 

Tests and measurements are controlled by a program which will set most parameter automatically. For any relevant standard, which are fulfilled by the MGA 1033, limit values are already included into the software package, although any different value can be defined by a user. After every test full reports will be created automatically. Report layout is pre-defined, though any user-defined layout is possible.

 

High performance is guaranteed by a self-calibration process which utilizes an internal source as reference.

 

Benefits

 Components MGA 1033 consists of three independent module: a signal generator (DC – 250 kHz), a power amplifier (800W output maximum, DC – 1MHz bandwidth) and spectrum analyzer (16 Bit, 1 MSPS sampling rate). All modules can be used as stand-alone units.  Software Any function is controlled via an application which also guide the user through any test or measurement. Configuration of signal strength or measurement graphs are possible at any stage. User defined signals complement the usage for fast and reliable tests. The application software is written in LabVIEW which guarantees stable and fast performance on any Microsoft® Windows platform

 Additional equipment We do also provide many different coils and loop sensors which are ideally suited for the described tests. Not only our own equipment can be used with the MGA 1033, but also user defined coils. A calibration mode is included in the software to complement the magnetic test system with any further equipment.

 

Aaronia_AG_BicoLOG_5070_Biconical_Antenna_Data_Sheet Schlöder MGA 1033 Magnetic Field System DC 250kHz Data Sheet

 

Aaronia_AG_BicoLOG_5070_Biconical_Antenna_Data_Sheet Schlöder MGA 1033 Magnetic Field System DC 250kHz Operation Manual

 

Accessories

• Coupling Networks – 3 Phase

• SFT 415 Capacitive Coupling Clamp

• SFT 415 – CS: Calibration Set for CCC

• SFT 450-1 (50 Ohm) and SFT 450-2 (1000 Ohm) Attenuators

• SFT 470 Probe Set – Magnetic Field

• SESD 30 S 100 ESD-Soft 6 ESD Remote Control Software