EnglishPortugueseSpanish

Request a Quote / Contact Us!

    Manufacturer

    Part Number or Numbers

    Voltage Probes

     

    • TK 9261 Active Voltage Probe 0.1-100MHz

    • TK 9417 HF Probe

    • TK 9420 High Voltage Probe

    • VT 9420 Plug-In Divider

    • TK 9421 High Power Voltage Probe

    • TK 9422 High Power Voltage Probe

     

    In addition to EMI measurement with LISNs (Line Impedance Stabilization Networks, Artificial Mains Networks), Probes are used for Terminal or Line voltage measurement.

    LISNs are required to feed the Equipment under Test (EUT) with mains power, to reduce external line interference, to offer the EUT a standardized impedance and to route the extracted r.-f. voltage to the EMI receiver.

    Probes are used for terminal voltage measurement, also on cables, output sockets, PCB traces. In many cases high input impedance and low capacitance is required for this purpose.

    Active Probes may not be used for general Interference measurement, as pulses could by far exceed the linear voltage range. This not only causes limiting and distortion effects but also inter-modulation that changes the frequency distribution of spectral components.
    These resistive dividing probes are perfectly linear and free of these effects.
    By the use of an AC and pulse-compatible input blocking capacitor (that is also free of partial discharge effects), EMI measurement is also possible on AC power lines up to 250 V ac or DC sources up to 500 V.
    High-Voltage Probes up to 10 kV (20 kV) DC or 2 kV AC with 1500 Ω input || 4 pF input capacity are available as TK 9420.
    For the max. power line voltage of 250 V ac two probes are available with input resistances of 1.5 kΩ, and 2.5 kΩ with the model numbers TK 9420, and TK 9417.

     

    TK 9261 Active Voltage Probe 0.1-100MHz 

    Schwarzbeck TK 9261 Active Voltage Probe 0.1-100MHz

    The TK 9261 is an active high-impedance RF voltage probe equipped with an internal impedance transformer which allows using it with 50 Ω measurement devices (such as spectrum and network analyzers or test receivers).

    Nominal frequency range (±1 dB):

     100 kHz – 100 MHz

    Useable frequency range:(±3 dB):

     50 kHz – 700 MHz

    Input damping resistance:

     >100 kΩ

    Input capacitance:

     1.8 pF typ.

    Output impedance:

     50 Ω

    Gain:

     0 dB

    Maximum output level:

     1.4 V peak

    Maximum input d.c. level:

     500 V

    Maximum input a.c. level:

     10 Vp-p

    Output:

     N-plug

    According to:

     Renault 36-00-808

    Power supply:

     +12…15 V
    50 mA

    DC-connector:

     5.5 mm / 2.5 mm

    Ambient temperature:

     -10° … +60°C

    Weight:

     300 g

     

    Schwarzbeck TK 9422 High Power Voltage Probe Data Sheet TK 9261 Active Voltage Probe 0.1-100MHz Data Sheet

     

     

    TK 9417 HF-Probe 
    schwarzbeck-tk-9417

    · HF-Probe

    · 2.5 kOhm
    Schwarzbeck TK 9417  RF Probe Data Sheet Data sheet TK9417

     

    TK 9420 High Voltage Probe 

    Schwarzbeck TK 9420 High Voltage Probe

    · High-Voltage-Probe

    · 1.5 kOhm

    · 4 pF

    · 9 kHz – 30 MHz

    · RF < 30 V

     

    Schwarzbeck TK 9420 Voltage Probe Data Sheet Data sheet TK 9420

     

    VT 9420 Plug-In Divider 

    Schwarzbeck VT 9420 Plug-In divider 1.5 kOhm for TK 9420 probe

    · Plug-In divider 1.5 kOhm for TK 9420 probe for determination of disturbance source impedance

    Schwarzbeck TK 9420 Voltage Probe Data Sheet Data sheet VT 9420

     

    TK 9421 High Power Voltage Probe 
    schwarzbeck-tk-9421

    · High Power Voltage Probe

    · 1.5 kOhm

    · 4 pF

    · 150 kHz – 30 MHz

    · RF < 100 V

     Schwarzbeck TK 9421 High Power Voltage Probe Data Sheet Data sheet TK9421

    TK 9422 High Power Voltage Probe 
    schwarzbeck-tk-9421

    · High Power Voltage Probe

    · 5 kOhm

    · 4 pF

    · (9) 150 kHz – 30 MHz

    · RF < 100 V

     Schwarzbeck TK 9422 High Power Voltage Probe Data Sheet Data sheet TK9422