MK-MESSTECHNIK Price List

	mk-messtechnik GmbH
Model #	Product Description	qty
optoLVDS-1 UB913/914	optical link for LVDS signals with chipset DS90UB913/914 integrated bidirectional control channel, setting of options/registers by switches / USB-interface (internal µ-controller with Windows application)
optoLVDS-1 UB913/914 Transmitter	optical transmitter for single-channel LVDS signals LVDS-connector: SMA + adapter to SMB (compatible to Fakra) optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation	1
optoLVDS-1 UB913/914 Receiver	optical receiver for single-channel LVDS signals from optoLVDS-1 UB913/914 Transmitter LVDS-connector: SMA + adapter to SMB (compatible to Fakra) optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation	1
SMA(m)-Fakra(m) adapter incl lock	adapter for optoCML or LVDS links with integrated SMA plug to connect standard female plug coaxial Fakra cable, with integrated lock	2
mkConfigSW	Windows application for setting of options/registers (of the internal μ-controller) on USB stick	1
C-USB2.0 A-B	standard USB cable, length approx. 1.8m Connectors: type-A – type-B	1
CH-1-5m	standard plug-in charger (e.g. Friwo) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah, AC-input: 100-240V, charge current: 600-800mA, charge connector: 5 pole male, AC-plug: Type A (US)	2
LWL-2 20m	duplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
LVDS – FPDIII or GMSL2 initial setup support	mandatory minimum initial setup support via phone / mail to be ordered with any «new» complex LVDS link. Only needs to be ordered one time. If you order the same link again and have experience with the setup, please state this in the request and refer to the according serial number and this position could be omitted.	1
Et-1h	Engineer work time [h]	8
optoTTL base unit	optoTTL base unit digital optical transmission of digital signals (base unit) can be used for PWM signals with min. pulse width of 5μs (sample rate faster than 1μs) 1 up to 16 digital channels «optoTTL-channel» integratable
optoTTL Transmitter base unit	optoTTL Transmitter base unit optical transmitter for 1 .. 16 digital channels (need to be ordered separately) 2 input ranges: 0/5V and 0/12V signal connector: SUB-D25 male frequency range: DC .. 1MHz (range of input filters), for digital signals up to 100kHz (each channel) optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation	1
optoTTL Receiver base unit	optoTTL Receiver base unit optical receiver for 1 .. 16 digital signals (from optoTTL Transmitter) output range: 0/5V (push/pul, max. approx. 20mA) signal connector: SUB-D25 female optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug	1
LWL-1 20m	LWL-1 20m simplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE in PO	2
optoTTL-channel	optoTTL-channel digital channel for optoTTL link optoTTL base unit needed up to 16 channels integratable (in both directions) => if bidirectional, each channel has to be added twice, e.g. 16 channel bidirectional is 32 channels	1
optoTTL option -b	optoTTL option -b option to use optoTTL bidirectional; simplex fiber replaced by duplex fiber; name number of channels for each direction optoTTL base unit needed 2x ALC => CR 2x CR => ALC	1
optoCAN-FD	optoCAN-FD – optical link for high speed CAN-signals with up to 10Mbit/s (max. 20m fiber). Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS75-5m (standard non shielded wall plug power supply to be used outside ALC)
optoCAN-FD Transceiver	optoCAN-FD Transceiver – optical transceiver for high-speed-CAN CAN-interface: max. 10MBit/s (up to 20m optical fiber) CAN-transceiver: TJA1044GT CAN-choke: B82789C0513N002, 51uH (others on request) CAN-connector: SUB-D9 optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, prepared for external supply; documentation available option: 19″ rack mount (for several automotive links in 2HU)	2
LWL-2 b20	LWL-2 b20 – Duplex optical fiber (62,5/125μm), length up to 20m, FSMA-FSMA Please name requested length in purchase order!	1
CH-1-5m	CH-1-5m – standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	2
external CAN-HS/FD protector	external CAN-HS/FD protector – termination 120Ohm (metal) to be used for EMS/EME-testing metal housing with connection plate enables GND connection if wanted/needed	1
optoCAN-HS	optoCAN-HS – optical link for high speed CAN-signals with up to 1Mbit/s (max. 20m fiber) Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS75-5m (standard non shielded wall plug power supply to be used outside ALC)
optoCAN-HS Transceiver	optoCAN-HS Transceiver – optical transceiver for high-speed-CAN CAN-interface: max. 1MBit/s (up to 20m optical fiber) CAN-transceiver: TJA1049 T (others on request) CAN-choke: B82789C0513N002, 51uH (others on request) CAN-connector: SUB-D9 optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, prepared for external supply; documentation available option: 19″ rack mount (for several automotive links in 2HU)	2
LWL-2 b20	LWL-2 b20 – Duplex optical fiber (62,5/125μm), length up to 20m, FSMA-FSMA Please name requested length in purchase order!	1
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	1
external CAN-HS/FD protector	external CAN-HS/FD protector – termination 120Ohm (metal) to be used for EMS/EME-testing metal housing with connection plate enables GND connection if wanted/needed	1
optoCAN-FD
external CAN-HS/FD protector	external CAN-HS/FD protector – termination 120Ohm (metal) to be used for EMS/EME-testing metal housing with connection plate enables GND connection if wanted/needed
optoCAN-LS	optoCAN-LS – optical link for low speed CAN-signals with up to 125kbit/s Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS75-5m (standard non shielded wall plug power supply to be used outside ALC)
optoCAN-LS Transceiver	optoCAN-LS Transceiver – optical transceiver for low-speed-CAN CAN-interface: max. 125kBit/s CAN-transceiver: TJA1055 (others on request) CAN-connector: SUB-D9 optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, prepared for external supply; documentation available option: 19″ rack mount (for several automotive links in 2HU)	2
LWL-2 20m	LWL-2 20m – duplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
CH-1-5m	CH-1-5m – standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	2
external CAN-LS	external CAN-LS protector (metal) to be used for EMS/EME-testing metal housing with connection plate enables GND connection if wanted/needed	1
optoCAN-SW	optoCAN-SW – optical link for low speed single wire CAN-signals with up to 83kbit/s. Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS75-5m (standard non shielded wall plug power supply to be used outside ALC)
optoCAN-SW Transceiver	optoCAN-SW Transceiver – optical transceiver for single wire low-speed-CAN CAN-interface: max. 83kBit/s CAN-transceiver: NCV7356 (others on request) VBat: external 6..13,5V or internal 12V CAN-connector: SUB-D9 optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, prepared for external supply; documentation available option: 19″ rack mount (for several automotive links in 2HU)	2
LWL-2 20m	LWL-2 20m – duplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	2
external LIN/K-Line/CAN-SW protector	external LIN/K-Line/CAN-SW protector (metal) to be used for EMS/EME-testing metal housing with connection plate enables GND connection if wanted/needed	1
optoLIN
optoLIN Transceiver	optoLIN Transceiver LIN-interface: max. 20kBit/s, for 12V and 24V applications LIN-transceiver: TJA1021 (others on request) LIN-connector: SUB-D9 optical connector: FSMA Shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation available option: 19″ rack mount (for up to 10 automotive links in 2HU)	2
LWL-2 20m	LWL-2 20m – duplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	2
external LIN/K-Line/CAN-SW protector	external LIN/K-Line/CAN-SW protector (metal) to be used for EMS/EME-testing metal housing with connection plate enables GND connection if wanted/needed	1
External Protection	External LIN/K-Line/CAN-SW protector (metal) to be used for EMS/EME-testing. Metal housing with connection plate enables GND connection if wanted/needed	1
optoK	optoK – optical link for K-Line signals with up to 30kbit/s Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS75-5m (standard non shielded wall plug power supply to be used outside ALC)
optoK Transceiver	optoK Transceiver K-Line interface: max. 30kBit/s (higher speed on request), for 12V and 24V applications K-Line connector: SUB-D9 optical connector: FSMA Shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation available option: 19″ rack mount (for up to 10 automotive links in 2HU)	2
CH-1-5m	CH-1-5m – standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	2
LWL-2 20m	LWL-2 20m – duplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
external LIN/K-Line/CAN-SW protector (metal)	external LIN/K-Line/CAN-SW protector (metal) – to be used for EMS/EME-testing metal housing with connection plate enables GND connection if wanted/needed	1
U1/12	U1/12 digital optical transmission of analog signals 1 analog channel, resolution min. 10bit, min. accuracy 1% of full range, bandwidth max. 10MHz (-3dB) NEW: output filter included Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS75-5m (standard non shielded wall plug power supply to be used outside ALC)
U1/12 Transmitter	U1/12 Transmitter input voltage +/- 15V connector: BNC optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation	1
U1/12 Receiver	U1/12 Receiver output voltage +/- 15V connector: BNC optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug	1
FI-1-10M-BNC	FI-1-10M-BNC external input filter to be used for EMS/EME-testing with Ux/14 or U2/12 connectors: BNC cutoff frequency (-3dB): 10MHz division ratio: 1:1	1
FI-1-1M-BNC	FI-1-1M-BNC external input filter to be used for EMS/EME-testing with Ux/14-1M or U2/12 connectors: BNC cutoff frequency (-3dB): 1MHz division ratio: 1:1	1
FO-FB-BNC	FO-FB-BNC external output filter applicable for analog transmission links (Ux/12, Ux/14 etc.) with BNC output connector. needs to be connected to the output of the receiver, if a stimulus is supposed to be sent to the inside of the ALC (receiver located in ALC, transmitter located in CR). setup with ferrite bead reduces overshoots of rectangular signals.	1
LWL-1 20m	LWL-1 20m – simplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	2
U1/12-1M	U1/12-1M digital optical transmission of analog signals 1 channel, resolution min. 10bit, min. accuracy 1% of full range, bandwidth max. 1MHz (-3dB) NEW: output filter included Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS75-5m (standard non shielded wall plug power supply to be used outside ALC)
U1/12-1M Transmitter	U1/12-1M Transmitter input voltage +/- 15V connectors: BNC optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation	1
U1/12-1M Receiver	U1/12-1M Receiver output voltage +/- 15V connectors: BNC optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug	1
FI-1-1M-BNC	FI-1-1M-BNC external input filter to be used for EMS/EME-testing with Ux/14-1M or U2/12 connectors: BNC cutoff frequency (-3dB): 1MHz division ratio: 1:1	1
FO-FB-BNC	FO-FB-BNC external output filter applicable for analog transmission links (Ux/12, Ux/14 etc.) with BNC output connector. needs to be connected to the output of the receiver, if a stimulus is supposed to be sent to the inside of the ALC (receiver located in ALC, transmitter located in CR). setup with ferrite bead reduces overshoots of rectangular signals.	1
LWL-1 20m	LWL-1 20m – simplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	2
U2/12-1M	U2/12-1M digital optical transmission of analog signals 2 channels, resolution min. 10bit, min. accuracy 1% of full range, bandwidth max. 1MHz (-3dB) NEW: output filters included Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS75-5m (standard non shielded wall plug power supply to be used outside ALC)
U1/12 Transmitter	U1/12 Transmitter input voltage +/- 15V connector: BNC optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation	1
U1/12 Receiver	U1/12 Receiver output voltage +/- 15V connector: BNC optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug	1
FI-1-1M-BNC	FI-1-1M-BNC external input filter to be used for EMS/EME-testing with Ux/14-1M or U2/12 connectors: BNC cutoff frequency (-3dB): 1MHz division ratio: 1:1	1
FO-FB-BNC	FO-FB-BNC external output filter applicable for analog transmission links (Ux/12, Ux/14 etc.) with BNC output connector. needs to be connected to the output of the receiver, if a stimulus is supposed to be sent to the inside of the ALC (receiver located in ALC, transmitter located in CR). setup with ferrite bead reduces overshoots of rectangular signals.	1
LWL-1 20m	LWL-1 20m – simplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	2
U2/12	U2/12 digital optical transmission of analog signals 2 analog channels, resolution min. 10bit, min. accuracy 1% of full range, bandwidth max. 10MHz (-3dB) NEW: output filters included Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS75-5m (standard non shielded wall plug power supply to be used outside ALC)
U1/12 Transmitter	U1/12 Transmitter input voltage +/- 15V connector: BNC optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation	1
U1/12 Receiver	U1/12 Receiver output voltage +/- 15V connector: BNC optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug	1
FI-1-10M-BNC	FI-1-10M-BNC external input filter to be used for EMS/EME-testing with Ux/14 or U2/12 connectors: BNC cutoff frequency (-3dB): 10MHz division ratio: 1:1	1
FI-1-1M-BNC	FI-1-1M-BNC external input filter to be used for EMS/EME-testing with Ux/14-1M or U2/12 connectors: BNC cutoff frequency (-3dB): 1MHz division ratio: 1:1	1
FO-FB-BNC	FO-FB-BNC external output filter applicable for analog transmission links (Ux/12, Ux/14 etc.) with BNC output connector. needs to be connected to the output of the receiver, if a stimulus is supposed to be sent to the inside of the ALC (receiver located in ALC, transmitter located in CR). setup with ferrite bead reduces overshoots of rectangular signals.	1
LWL-1 20m	LWL-1 20m – simplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	2
U8/12-1M – shielded receiver	U8/12-1M – shielded receiver for digital optical transmission of analog signals 8 channels, resolution min. 10bit, bandwidth max. 1MHz (-3dB); min. accuracy 1% of full range external battery pack for one device included to extend system runtime NEW: output filters included
U8/12-1M Transmitter	U8/12-1M Transmitter input voltage +/- 15V; external filters/voltage dividers connectors: BNC optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation	1
U8/12-1M Receiver	U8/12-1M Receiver – shielded output voltage +/- 15V connectors: BNC optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation AC-plug: Type C – Europe (Standard, Type A (US) or G (UK) avbl. STATE IN PO!)	1
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	1
FI-1-1M-BNC	FI-1-1M-BNC external input filter to be used for EMS/EME-testing with Ux/14-1M or U2/12 connectors: BNC cutoff frequency (-3dB): 1MHz division ratio: 1:1	1
FO-FB-BNC	FO-FB-BNC external output filter applicable for analog transmission links (Ux/12, Ux/14 etc.) with BNC output connector. needs to be connected to the output of the receiver, if a stimulus is supposed to be sent to the inside of the ALC (receiver located in ALC, transmitter located in CR). setup with ferrite bead reduces overshoots of rectangular signals.	1
BP84-5f	BP84-5f 8,4V NiMH battery pack, capacity 4Ah in shielded metal housing with rubber protectors; suitable for optoUSB, U8/12-1M and others, 5 pole female charge plug without shielded cable, needs to be added separately	1
SC-30-5m5m	SC-30-5m5m Shielded cable with folding ferrites. To be used with battery packs BPxx or shielded power supplies SPSxx to power devices during EMC-tests Length: 30cm Connectors: Binder series, male 5-pole – male 5-pole	1
PS120-5m	PS120-5m external power supply (not for use inside ALC during EMC-tests!) input: 100 .. 240VAC; 50 .. 60Hz; output: 12V/1.5A connector: 5-pole male, Binder series AC-plug: Type C – Europe (Standard, Type A (US) or G (UK) avbl. STATE IN PO!)	1
LWL-1 20m	LWL-1 20m – simplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
U8/12-1M – table top receiver	U8/12-1M – table top receiver digital optical transmission of analog signals 8 channels, resolution min. 10bit, bandwidth max. 1MHz (-3dB); min. accuracy 1% of full range external battery pack for transmitter to extend system runtime optical receiver in non-shielded table top housing with standard power supply
U8/12-1M Transmitter	U8/12-1M Transmitter input voltage +/- 15V; external filters/voltage dividers connectors: BNC optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation	1
U8/12-1M Receiver	U8/12-1M Receiver – shielded output voltage +/- 15V connectors: BNC optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation AC-plug: Type C – Europe (Standard, Type A (US) or G (UK) avbl. STATE IN PO!)	1
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	1
FI-1-1M-BNC	FI-1-1M-BNC external input filter to be used for EMS/EME-testing with Ux/14-1M or U2/12 connectors: BNC cutoff frequency (-3dB): 1MHz division ratio: 1:1	1
BP84-5f	BP84-5f 8,4V NiMH battery pack, capacity 4Ah in shielded metal housing with rubber protectors; suitable for optoUSB, U8/12-1M and others, 5 pole female charge plug without shielded cable, needs to be added separately	1
SC-30-5m5m	SC-30-5m5m Shielded cable with folding ferrites. To be used with battery packs BPxx or shielded power supplies SPSxx to power devices during EMC-tests Length: 30cm Connectors: Binder series, male 5-pole – male 5-pole	1
PS120-5m	PS120-5m external power supply (not for use inside ALC during EMC-tests!) input: 100 .. 240VAC; 50 .. 60Hz; output: 12V/1.5A connector: 5-pole male, Binder series AC-plug: Type C – Europe (Standard, Type A (US) or G (UK) avbl. STATE IN PO!)	1
LWL-1 20m	LWL-1 20m – simplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
optoLAN	optical link for high speed Ethernet (LAN) signals with up to 100Mbit/s (100BaseTx). Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS75-5	1
optoLAN Transceiver	LAN-interface: max. 100Mbit/s (100BaseTx); 10BaseTx not supported LAN-connector: RJ45 optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, prepared for external supply; documentation	2
LWL-2 20m	duplex optical fiber (62,5/125µm), length 20m, FSMA-FSMA	1
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!) AC-plug: Type A (US)	2
optoLAN -option M12	replaces RJ45 connector on one transceiver by 4-pole Metz connect M12 plug (field configurable emc hardened) order twice if requested for both transceivers	1
Metz M12 4 pole male- plug to RJ45 adapter cable	Cable with Metz Connect M12 4 pole male plug to RJ45 male plug. High quality fully shielded confectioned solution to connect optoLAN-100Mb transceiver directly to DUT. Length: ~2m. Accessory for -option M12, different lengths available on request	1
5 cell external power pack	external power pack that includes a 5 cells (6V) shielded battery pack BP60-5f (only to be used with optical links that do have 5 cells (6V) batteries integrated (see rear side of devices) shielded connection cable and a external wall plug power supply unit to be used outside the chamber to constantly power a device. DO NOT mistake a «charger» (CH-1-5m) for a «constant power supply» (PS-75-5m)! optional	1
BP60-5f	6V NiMH battery pack, capacity 4Ah in shielded metal housing with rubber protectors; suitable for U2/12, U16/12-100k, optoRS232, RS485, optoCAN, optoFlex, optoLIN, and others, 5 pole female charge plug	1
SC-30-5m5m	Shielded cable with folding ferrites. To be used with battery packs BPxx or shielded power supplies SPSxx to power devices during EMC-tests. Length: 30cm. Connectors: Binder series, male 5-pole – male 5-pole	1
PS75-5m	external power supply (only for CR use; not for use inside ALC during EMC-tests!). input: 100 .. 240VAC; 50 .. 60Hz; output: 7.5V/1A connector: 5 pole male, Binder series AC-plug: Type A (US)	1
optoLAN-Gb	optoLAN-Gb optical link for high speed Ethernet (LAN) signals with up to 1Gbit/s; one unit equipped with M12 plug for improved emc performance; standard adapter cable (M12-RJ45) 2m included, others on request DUT / counterpart needs «auto negotiation» functionality to automatically detect 100MBit/s; else, the device has to be programmed from externally Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS75-5m (standard non shielded wall plug power supply to be used outside ALC)
optoLAN-Gb Transceiver	optoLAN-Gb Transceiver LAN-interface: max. 1Gbit/s (10BaseTx, 100BaseTx and 1000BaseTx automatically detected) LAN-connector: RJ45 optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, prepared for external supply; documentation	1
optoLAN-Gb Transceiver -M12	optoLAN-Gb Transceiver -M12 LAN-interface: max. 1Gbit/s (10BaseTx, 100BaseTx and 1000BaseTx automatically detected) LAN-connector: M12, improved shield connection, to be used inside ALC for high emc performance M12 plug pining: 1: D1_P + 2: D1_N 3: D2_P + 4: D2_N 5: D3_P + 6: D3_N 7: D4_P + 8: D4_N optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, prepared for external supply; documentation	1
Metz M12 8	Metz M12 8 pole male- plug to RJ45 adapter cable with Metz Connect M12 8 pole male plug to RJ45 male plug high quality fully shielded confectioned solution to connect optoLAN-GB transceiver directly to DUT length: ~2m accessory for M12 plug connector, different lengths available on request	1
LWL-1 20m	LWL-1 20m – simplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	2
optoLAN-BCM89810	optical link for 100Base-T1 automotive Ethernet signals with Broadcom BCM89810 chipset setup: 100BaseT1 => 100BaseT1 (standard); integrated media converter on request Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS75-5m (standard non shielded wall plug power supply to be used outside ALC)
optoLAN-BCM89810 Transceiver	optoLAN-BCM89810 Transceiver optical transceiver for automotive Ethernet transceiver Broadcom BCM89810 optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, prepared for external supply; documentation BRReach connector: Rosenberger HSD	2
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type A (US)	2
LWL-2 20m	LWL-2 20m duplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
optoLAN-BCM89811	optoLAN-BCM89811 optical link for 100Base-T1 automotive Ethernet signals with Broadcom BCM89811 chipset setup: 100BaseT1 => 100BaseT1 (standard); integrated media converter on request Termination according to Open Alliance standard Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS75-5m (standard non shielded wall plug power supply to be used outside ALC)	1
optoLAN-BCM89811 Transceiver	optoLAN-BCM89811 Transceiver optical transceiver for automotive Ethernet transceiver Broadcom BCM89811 Termination setup according to Open Alliance standard optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, prepared for external supply; documentation BRReach connector: Rosenberger HSD	2
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type A (US)	2
LWL-2 20m	LWL-2 20m duplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
Rosenberger HSD cable Z – open end	cable with Rosenberger HSD universal coded connector – open end for self configuration length: ~2m color coding Side A: 1: blue 2: orange 3: green 4: brown color coding Side B: 1: brown 2: green 3: orange 4: blue	1
optoUSB2.0 -RBDIR	optoUSB2.0 -RBDIR optical link for transmission of USB2.0 signals (max. 480Mbit/s) with EMC improved Rosenberger HSD connector Optional available external power supplies – prices on request: BP84-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP84-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS120-5m (standard non shielded wall plug power supply to be used outside ALC)
optoUSB2.0 -RBDIR Transceiver-Hub	optoUSB2.0 -RBDIR Transceiver-Hub USB-connector (Hub): 1x type-A; 1x Rosenberger HSD HSD-pin out (identical on both transceivers): 1: Data + 2: VCC 5V (max 500mA) 3: Data – 4: GND Shield switch for 2 different operating modes: HUB or direct switch for internal/external power supply at USB-ports with LED-indicator (5V on/off); max 500mA optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation	1
optoUSB2.0 -RBDIR Transceiver-PC	optoUSB2.0 -RBDIR Transceiver-PC USB-connector (to PC): 1x type-B, 1x Rosenberger HSD; selectable via switch HSD-pin out (identical on both transceivers): 1: Data + 2: VCC 5V (max 500mA) 3: Data – 4: GND Shield optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug	1
C-USB2.0 A-B	C-USB2.0 A-B standard USB cable, length approx. 1.8m Connectors: type-A – type-B	1
LWL-1 20m	LWL-1 20m – simplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	2
	Rosenberger HSD cables Z – USB
Type A female plug	Rosenberger HSD cable Z – USB Type A female plug short adapter cable with Rosenberger HSD universal coded connector – Type A female plug high quality fully shielded confectioned solution to connect Hub side transceiver to DUT (e.g. webcam) with original wire harness length: ~0.2m
Type A male plug	Rosenberger HSD cable Z – USB Type A male plug cable with Rosenberger HSD universal coded connector – Type A male plug high quality fully shielded confectioned solution for direct DUT connection (connect PC side USB transceiver directly to DUT => e.g. PC) length: ~2m
Type B male plug	Rosenberger HSD cable Z – USB Type B male plug cable with Rosenberger HSD universal coded connector – Type B male plug high quality fully shielded confectioned solution to connect Hub side USB transceiver directly to DUT (e.g. webcam) length: ~2m
optoRS232-HS	optoRS232-HS optical transmission of serial RS232 signals with handshake data rate: max. 116kBit/s Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS75-5m (standard non shielded wall plug power supply to be used outside ALC)
optoRS232-HS Transceiver-DUT	optoRS232-HS Transceiver-DUT RS232 connector: SUB-D 9 male plug Optical connector: FSMA Shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation	1
optoRS232-HS Transceiver-PC	optoRS232-HS Transceiver-PC RS232 connector: SUB-D 9 female plug Optical connector: FSMA Shielded metal housing with integrated NiMH batteries, 5-pole female charge plug	1
LWL-1 20m	LWL-1 20m – simplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	2
optoRS485	optoRS485 optical transmission of serial RS485 signals. signals: Data + / Data – data rate: max. 1MBit/s, depending on signal integrity (cabling, etc..) Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS75-5m (standard non shielded wall plug power supply to be used outside ALC)
optoRS485 Transceiver	optoRS485 Transceiver RS485 connector: SUB-D 9 male plug Optical connector: FSMA Shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation	2
LWL-1 20m	LWL-1 20m – simplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	2
dAV base unit
dAV Transmitter base	digital transmission of analog audio and/or video signals (depends on options) without inputs/outputs, please select options optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation
dAV Receiver base	digital transmission of analog audio and/or video signals (depends on options) without inputs/outputs optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug
LWL-1 20m	LWL-1 20m – simplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)
dAV option -a	option for dAV base unit: unidirectional digital transmission of analog stereo audio signals, frequency range: 20Hz .. 18kHz (3dB cutoff) I/O: single ended, >12kOhm, gain=1
dAV-TRX	dAV-TRX bidirectional intercom system made of dAV base unit with option -intercom
dAV-TRX-BP	dAV-TRX-BP digital optical intercom transceiver with integrated battery pack (to be used inside ALC) integrated loudspeaker and microphone with speak switch optical connector: 2x FSMA shielded metal housing, 5-pole female charge plug, documentation	1
dAV-TRX-table top	dAV-TRX-table top digital optical intercom transceiver with external power supply (to be used outside ALC) integrated loudspeaker and microphone with speak switch optical connector: 2x FSMA metal table top housing (no batteries integrated), standard 2-pole female power supply plug, documentation	1
dAV-TRX-table top -option goose neck mic	dAV-TRX-table top -option goose neck mic goose neck microphone for dAV-TRX table top transceiver instead of integrated microphone	1
LWL-1 20m	LWL-1 20m – simplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
CH-1-5m	CH-1-5m standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	1
PS75-2f	PS75-2f external power supply (not for use inside ALC during EMC-tests!) input: 100 .. 240VAC; 50 .. 60Hz; output: 7,5V/1A connector: 2 pole female AC-plug: Type C – Europe (Standard, Type A (US) or G (UK) avbl. STATE IN PO!)	1
LE-LED 150	LE-LED 150 LED chamber light with 4 spots and built in AC-DC converter
LE-LED 150	low emission ALC LED light with 4 spots and approx. 150W LED power can be easily exchanged with existing 230V chamber lights (halogen lights) 4 adjustable (one axis) full metal head LED spots single powered by a toroid core transformer in a full metal shield housing voltage power supply: 230V (standard, 110V on request) two different reflector types available: 45°: ~6,6m spot diameter when rectangular mounted in 8m distance: approx. 330 lux brightness 24°: ~3,4m spot diameter when rectangular mounted in 8m distance: approx. 750 lux brightness total weight approx 10kg ball head mount to additionally adjust the total light in a second axis included arresting cable included to secure lamp against dropping please ensure a minimum clearance of 30-50cm to ceiling to avoid overheating of LED-spots Total number of spots (name 4 in total): number of 24° spots: number of 45° spots:	1
M8-ballhead	M8-ballhead manual ballhead with M8 socket to mount and adjust LE-LEDs to an existing wall- or ceiling mount.	1

dAV-Cr-HD-mini LP	dAV-Cr-HD-mini LP (Long Play) high definition miniature camera (1080p) with digital optical transmission; mini HD-resolution camera (1080p) size: ~50x50x100mm remote controllable (from receiver or optional software or joystick remote table top) 10x optical zoom, focus, brightness, etc.; min. illumination: 0,5lux; additional functions like manual iris/shutter etc. controllable via optional software (-ccs). integrated mono-microphone; 3 pole male power plug; connector for optional pan/tilt-unit; optical connector: FSMA (simplex, signal and remote on one fiber), documentation
dAV-Cr-HD-mini	dAV-Cr-HD-mini high definition miniature camera (1080p) with digital optical transmission; mini HD-resolution camera (1080p) size: ~50x50x100mm remote controllable (from receiver or optional software or joystick remote table top) 10x optical zoom, focus, brightness, etc.; min. illumination: 0,5lux; additional functions like manual iris/shutter etc. controllable via optional software (-ccs). integrated mono-microphone; 3 pole male power plug; connector for optional pan/tilt-unit; optical connector: FSMA (simplex, signal and remote on one fiber), documentation
dAV-Cr-xD tripod mount	dAV-Cr-xD tripod mount. milled aluminum tripod mount adapter set for dAV-Cr-xD; screwed to the bottom of the camera with a 1/4″ screw hole to attach camera to any standard tripod satchet with screws and flat washers	1
SPS120-5f	linear controlled shielded external power supply, applicable for use with dAV-Cr input: 220 .. 240VAC; 50 .. 60Hz output: 12V/1A 5-pole female connection plug 110V available on request -> STATE IN PO power supply cable for 230V or 110V application, length approx. 1.8m AC-plug: Type F – Europe (Standard, Type B (US) or G (UK) avbl. STATE IN PO!) without shielded cable, needs to be added separately	1
SC-xxx-3f5m	Shielded cable with folding ferrites added for self configuration where possible, to be used with battery packs BP-120 or external shielded power supply SPS120-5f and dAV-C; Connectors: Binder series, female 3-pole – male 5-pole length: xxxm	1
LWL-1 20m	LWL-1 20m. simplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
CH-1-5m	CH-1-5m. standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	1

dAV-Cr-HD-mini-PS LP	dAV-Cr-HD-mini-PS LP (Long Play) high definition miniature camera (1080p) with digital optical transmission and shielded power supply for wall mount application
dAV-Cr-HD-mini-PS	dAV-Cr-HD-mini-PS high definition miniature camera (1080p) with digital optical transmission with shielded power supply for wall mount application; mini HD-resolution camera (1080p) size: ~50x50x100mm remote controllable (from receiver or optional software or joystick remote table top) 10x optical zoom, focus, brightness, etc.; min. illumination: 0,5lux; additional functions like manual iris/shutter etc. controllable via optional software (-ccs). integrated mono-microphone; 3 pole male power plug; connector for optional pan/tilt-unit; optical connector: FSMA (simplex, signal and remote on one fiber), shielded power supply for wall mount application, documentation
dAV-Cr-HD-mini	dAV-Cr-HD-mini high definition miniature camera (1080p) with digital optical transmission; mini HD-resolution camera (1080p) size: ~50x50x100mm remote controllable (from receiver or optional software or joystick remote table top) 10x optical zoom, focus, brightness, etc.; min. illumination: 0,5lux; additional functions like manual iris/shutter etc. controllable via optional software (-ccs). integrated mono-microphone; 3 pole male power plug; connector for optional pan/tilt-unit; optical connector: FSMA (simplex, signal and remote on one fiber), documentation	1
dAV-Cr-xD tripod mount	dAV-Cr-xD tripod mount. milled aluminum tripod mount adapter set for dAV-Cr-xD; screwed to the bottom of the camera with a 1/4″ screw hole to attach camera to any standard tripod satchet with screws and flat washers	1
SC-60-3f5m	SC-60-3f5m. Shielded cable with folding ferrites, to be used with battery packs BP-120 or external shielded power supply SPS120-5f and dAV-C; length: 60cm Connectors: Binder series, female 3-pole – male 5-pole	1
SC-140-3f5m	SC-140-3f5m. Shielded cable with folding ferrites, to be used with battery packs BP-120 or external shielded power supply SPS120-5f and dAV-C; length: 140cm Connectors: Binder series, female 3-pole – male 5-pole	1
LWL-1 20m	LWL-1 20m. simplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
BP-holder	battery pack holder with Velcro stripes; to be attached with Velcro e.g. to tripod to keep battery pack in place	1
dAV-Cr-HD	high definition camera (1080p) with digital optical transmission
dAV-Cr-HD	HD-resolution camera (1080p) manual (at camera rear side) and remote controllable (from receiver or optional software or joystick remote table top) 20x optical zoom, focus, brightness, short range LED-lights, etc.; min. illumination: 0,1lux; additional functions (manual iris/shutter etc.) controllable via optional software (-ccs) integrated mono-microphone; 3 pole male power plug; connectors for external set-up display, optional pan/tilt-unit; optical connector: FSMA (simplex, signal and remote on one fiber), documentation	1
dAV-Cr-xD Tripod Mount	milled aluminum tripod mount adapter set for dAV-Cr-xD; screwed to the bottom of the camera with a 1/4″ screw hole to attach camera to any standard tripod satchet with screws and flat washers	1
BP120-5f	12V NiMH battery pack, capacity 4Ah in shielded metal housing with rubber protectors; suitable for dAV-C and others, 5 pole female charge plug without shielded cable, needs to be added separately	2
BP-holder	battery pack holder with Velcro stripes; to be attached with Velcro e.g. to tripod to keep battery pack in place;	1
SC-60-3f5m	Shielded cable with folding ferrites, to be used with battery packs BP-120 or external shielded power supply SPS120-5f and dAV-C; length: 60cm Connectors: Binder series, female 3-pole – male 5-pole	1
SC-140-3f5m	Shielded cable with folding ferrites, to be used with battery packs BP-120 or external shielded power supply SPS120-5f and dAV-C; length: 140cm Connectors: Binder series, female 3-pole – male 5-pole	1
LWL-1 20m	simplex optical fiber (62,5/125µm), length 20m, FSMA-FSMA	1
CH-1-5m	standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	1
ED-43	4,3″ new generation set-up display, to be used for camera set-up and installation before testing (only 20x and 30x HD and SD cameras have the proper connector, cannot be connected to mini or μ HD cameras), needs to be removed during test

PT-03 (LP)	PT-03 (LP). Mechanical robust pan/tilt unit for mobile use (e.g. on tripod)	1
PT-03	PT-03. Mechanical robust pan/tilt unit for mobile use (e.g. on tripod)
PT-03-sc	PT-03-sc. pan/tilt unit with mechanical robust mounting for camera dAV-Cr with 1/4″ standard tripod thread mount; shielded metal housing; powered by camera with shielded cable (separate position) standard range horizontal: approx. +/- ~90°, standard range vertical: approx. +/- ~45°, «Move» AND «set limit» buttons to be able to turn the pan/tilt at place integrated safety clutch on both axes to prevent broken gears and motors due to force overload (e.g. from moving by hand) Also new and available on request: optional mk one hand quick release	1
SC-35-4m4m	SC-35-4m4m. Shielded cable with folding ferrites, to be used with pan/tilt unit (connection to camera); length: 35cm Connectors: Binder series, male 4-pole – male 4-pole	1

Monopod – wood	Monopod – mk monopod made of wood and glass fiber with quick release functionality
Monopod – wood	Monopod – wood. wooden monopod to mount dAV-Cr camera with pan/tilt (1/4″ thread) with height adjust possibility (~1,1m – 1,8m) and massive bottom stand. If no pan/tilt (PT-03) is ordered, the camera is mounted in straight position (optional manual pan/tilt available) standard: felt gliders (optional: casters) additional shipping costs apply	1
PT-0x option -quick release	PT-0x option -quick release. optional mk quick release for one hand use of PT-03/02 3/8 thread integrated: use adapter if 1/4″ thread needed! mandatory for monopod and wall mount	1
Hook-and-loop fastener	Hook-and-loop fastener, belt with buckle (metal) width = 25mm length adjusted to necessary value	1

Monopod -option locking casters (LP)	Monopod -option locking casters (LP). optional integrated locking casters for Monopod minimize danger to tip over, only for flat surfaces
dAV-Rr-HD TT	table top receiver for high resolution cameras equipped with minimum configuration (one HD-channel preinstalled). Can be equipped with max. 4 channels and various other options power supply upgraded depending on additional ordered options	1
dAV-Rr base TT	digital receiver base unit dAV-Rr (without inputs) for audio and video signal from dAV-Cr camera system. table top housing with 1 integrated loudspeaker. remote control front panel for main camera functions (zoom, focus, brightness, LED on/off and optional pan/tilt unit(s) integrated available options: OSD, remote table top interface, additional channels	1
dAV-Rr TT option -x	multi channel bus extension for dAV-Rr TT base unit receivers up to 4 dAV-Rr-xD-Ch (SD or HD) channels (retrofitting of additional channels possible) can be plugged in and are selectable for remote and audio out control (front speaker of receiver) via push buttons	1
dAV-Rr-HD-Ch	digital optical HD input electrical output board/channel for dAV-Rr-HD optical connector: FSMA output connectors: – VGA and DVI-D via adapter cradle or DVI-D direct, 16:9 1080p, use standard Full-HD TFT screen – CVBS 4:3 PAL (reduced quality for cheap recording possibilities) – audio via 3,5mm plug 3GSDI output optional available	2
dAV-R option -cominterface	interface card to connect external equipment: dAV-R option -OSD: on screen display dAV-R option -ccs: camera control software (allows firmware updates, remote control and debugging via USB connection) dAV-Rrc-Joy: RS485 connection for external table top joystick remote	1
DVI-HDMI Cable 2m	DVI-HDMI cable to connect receiver output to monitor with integrated audio length: 2m	1
PS75-2f	external power supply (only for CR use; not for use inside ALC during EMC-tests!) input: 100 .. 240VAC; 50 .. 60Hz; output: 7,5V/1A connector: 2 pole female AC-plug: Type C – Europe (Standard, Type A (US) or G (UK) avbl. STATE IN PO!)	1
	Individual Options
BP60-5f	6V NiMH battery pack, capacity 4Ah in shielded metal housing with rubber protectors; suitable for U2/12, U16/12-100k, optoRS232, RS485, optoCAN, optoFlex, optoLIN, and others, 5 pole female charge plug. Provides approximately 12 hours of additional use of the TRX intercom.	1
BP60/10-5f	6V NiMH battery pack, capacity 10Ah in shielded metal housing with rubber protectors; suitable for all 5 cell devices like analog links U2/12 and U16/14, optoRS232, RS485, optoCAN, optoFlex, optoLIN, and others, 5 pole female charge plug bigger (longer) size of housing without shielded cable, needs to be added separately extra charger recommended to avoid issues due to high capacity – if ordered together with optical link, the links chargers will be upgraded free of charge. Provides approximately 30 hours of additional use of the TRX intercom.	1
SC-30-5m5m	SC-30-5m5m – Shielded cable with folding ferrites. To be used with battery packs BPxx or shielded power supplies SPSxx to power devices during EMC-tests. Length: 30cm Connectors: Binder series, male 5-pole – male 5-pole	1
tripod-mini	wooden mini tripod with 1/4″ camera adapter minimum height: 5 cm = 2 inch (no tilt possible) maximum height: 36 cm = 14 inch tilt via leg spread	1
Monopod – head	wooden monopod head to mount dAV-Cr camera with pan/tilt (1/4″ thread) or manual ballhead If no pan tilt is included in PO, a ball head is used instead of the quick release alternative to tripod mini	1
Options
dAV-Rr-HD 19″	19″ rack mount receiver for high resolution cameras equipped with minimum configuration (one HD-channel preinstalled) can be equipped with max. 8 (4×2 stacked) channels and various other options power supply upgraded depending on additional ordered options
dAV-Rr base 19″	digital receiver base unit dAV-Rr (without inputs) for audio and video signal from dAV-Cr camera system 19″ rack mount (2HU) with 2 integrated loudspeakers remote control front panel for main camera functions (zoom, focus, brightness, LED on/off and optional pan/tilt unit(s)) integrated available options: multichannel receiver; OSD, remote table top interface	1
dAV-Rr 19″ option -x	multi channel bus extension for dAV-Rr 19″ base unit receivers up to 8 dAV-Rr-xD-Ch (SD or HD) channels (retrofitting of additional channels possible) can be plugged in and are selectable for remote and audio out control (front speaker of receiver) via push buttons	1
dAV-Rr-HD-Ch HDMI	digital optical HD input – electrical output board/channel for dAV-Rr-HD optical connector: FSMA output connectors: – HDMI, 16:9 1080p, use standard Full-HD TFT screen – CVBS 4:3 PAL (reduced quality for cheap recording possibilities) via BNC plug – Line audio via 3,5mm plug 3GSDI output optional available (as alternative to CVBS out – ask for details)	1
dAV-R option -cominterface	interface card to connect external equipment: dAV-R option -OSD: on screen display dAV-R option -ccs: camera control software (allows firmware updates, remote control and debugging via USB connection) dAV-Rrc-Joy: RS485 connection for external table top joystick remote	1
HDMI-HDMI cable 2m	HDMI-HDMI cable to connect recorder output to monitor length: 2m	1
PS75-2f	external power supply (only for CR use; not for use inside ALC during EMC-tests!) input: 100 .. 240VAC; 50 .. 60Hz; output: 7,5V/1A connector: 2 pole female AC-plug: Type C – Europe (Standard, Type A (US) or G (UK) avbl. STATE IN PO!)	1
dAV-Rr-HD-Ch HDMI	digital optical HD input board for dAV-Rr-HD with HDMI port
dAV-Rr-HD-Ch	digital optical HD input – electrical output board/channel for dAV-Rr-HD optical connector: FSMA output connectors: – HDMI, 16:9 1080p, use standard Full-HD TFT screen – CVBS 4:3 PAL (reduced quality for cheap recording possibilities) via BNC plug – Line audio via 3,5mm plug 3GSDI output optional available (as alternative to CVBS out – ask for details)	1
HDMI-HDMI cable 2m	HDMI-HDMI cable to connect recorder output to monitor length: 2m	1
dAV-R option -Ethernet	dAV-R option -Ethernet remote additional Ethernet interface card for option -cominterface to control all integrated receiver remote functions up to 8 control connections at the same time possible (ccs, OSD,..)	1
dAV-R option -OSD	dAV-R option -OSD. OSD function for dAV-R(r)-SD und dAV-Rr-HD. function: on screen display integratable in video stream e.g. frequency and field strength, time, date and DUT number (depending on your RF control software). Driver programming details included in manual NEW: with integrated battery and configurable (time display) real time clock to permanent display date/time without being connected to a PC	1
dAV-Rmrr option -ccs	camera control software option for all camera and pan/tilt functions control microphone gain, DVI/VGA output of receiver channels and additional camera parameters executable software GUI to be run e.g. from a documentation-PC (via USB2.0) (if Ethernet control is requested, add option dAV-R option Ethernet remote) optional but recommended delivered version:	1
dAV-Rrc-Joy	Joystick remote control to be connected to RS485 port of dAV-Rr-xD
dAV-Rrc-Joy	table top remote control for multiple cameras (max. 8) with Joystick and switch buttons interface: RS485 dAV-R option -r (remote control, included in dAV-Rr-HD) and dAV-R option -cominterface mandatory 12V receiver power supply necessary!	1
C-SUBD-500-9m9f	standard SUBD-9 cable, length approx. 5m connectors: SUBD-9 female – SUBD-9 male	1
dAV-quad-4K	quad view system to integrate and display 4 independent Full-HD 1080p60 inputs in one 4Kp30 resolution screen. Optional outputs possible to be able to display the same output on other screens, record in low quality or optically forward optional outputs: – 2nd HDMI (4Kp30 or 1080p60) – up to 2 optical outputs (1080p) additional – 3GSDI (1080p60 (Level A 4:2:2 YUV)
dAV-quad 4K	input video connectors: 4x HDMI/VGA (max. 1080p60) standard output video connector: 1x HDMI capable of 4Kp30 output control via integrated push buttons or software (GUI, over USB port) selectable modes: Full, quad, picture in picture	1
HDMI-HDMI cable 0,5m	HDMI-HDMI cable to connect HDMI out and In length: 0,5m	4
dAV-quad software	software GUI on USB stick to fully control all quad functions	1
PS120-2f	external power supply (only for CR use; not for use inside ALC during EMC-tests!) input: 100 .. 240VAC; 50 .. 60Hz; output: 12V/xA (adjusted to necessary value) connector: 2-pole female AC-plug: Type C – Europe (Standard, Type A (US) or G (UK) avbl. STATE IN PO!)	1
dAV-quad -option Ethernet remote	additional Ethernet interface card to control all integrated quad functions (dAV-quad software) via Ethernet up to 8 control connections at the same time possible
USB stick	standard USB2.0 stick, capacity approx. 4GB Connector: type-A	1
C-USB2.0 A-B	standard USB cable, length approx. 1.8m Connectors: type-A – type-B	1
dAV-R option -Hdrec LGP2	third party consumer electronic external 1 channel HD video signal recording option (USB video grabber for PC use) video connectors: HDMI In and HDMI Out (Loop through) audio connector: 3,5mm (or HDMI) video resolution: up to 1920x1080p30, changeable (to reduce amount of data) video quality: changeable (to reduce amount of data) storage: with PC (not included) software (to PC-HDD in 1080p format (can be changed in software too). Push button can remote control start/stop PC-recording). min requirements for PC usage: free USB port clock rate: >1.8GHz, multicore HDD: >1TB RAM: >4GB operating system: Microsoft ® Windows ® 8,7, 32 bit or 64 bit PC must be located near grabber (only short USB cable allowed) including 1x ~1.5m HDMI – DVI cable to connect to dAV-Rr-HD-CH and 1x ~1.5m HDMI-HDMI cable to connect loop through output to a standard TFT screen with HDMI In	1
dAV-R option -HDrec PCI	dAV-R option -HDrec PCI 1 channel HD video signal grabber card (PCIe Gen1 x1) with custom mk recorder / snapshot software. => card and software need to be installed on site video connectors: HDMI In and HDMI Out (Loop through) audio connector: 3,5mm (or HDMI) video capturing resolution: up to 1920x1080p30, changeable (to reduce amount of data) with H.264 encoding video quality: changeable (to reduce amount of data) Optional mk push button (USB / Ethernet available) can remote control start/stop PC-recording (dAV-R option -HDrec external push button) min requirements for PC usage: free PCIe Gen 1 x1 port clock rate: Intel i5, >2GHz, multicore HDD: >1TB RAM: >4GB required operating system: Microsoft ® Windows ® 10, 8,7, 32 bit or 64 bit including 1x ~1.5m HDMI – DVI cable to connect loop through output to a standard TFT screen with DVI In	1
LCD-24″ VGA/DVI	24″ flat screen monitor (LED, IPS) input: VGA/DVI resolution: Full-HD 1920 x 1080 * extra shipping cost applies (weight and size) * AC-plug: Type C – Europe (Standard, Type A (US) or G (UK) avbl. STATE IN PO!)	1

PT-02 LP	LP version of pan/tilt unit for wall mount application	1
PT-02	pan/tilt unit for wall mount application
PT-02-sc	pan/tilt unit for camera dAV-Cr with 1/4″ standard thread mount; shielded metal housing; powered by camera with shielded cable (separate position) standard range horizontal: approx. +/- ~90° standard range vertical: approx. +/- ~45° «Move» AND «set limit» buttons to be able to turn the pan/tilt at place integrated safety clutch on both axes to prevent broken gears and motors due to force overload (e.g. from moving by hand) standard programmed for wall mount application. Please inform us, if ceiling mount is required left/right and up/down directions need to be inverted) Also new and available on request: optional mk one hand quick release	1
SC-35-4m4m	SC-35-4m4m. Shielded cable with folding ferrites, to be used with pan/tilt unit (connection to camera); length: 35cm Connectors: Binder series, male 4-pole – male 4-pole	1

Monopod (LP)	Monopod (LP) – mk monopod made of wood and glass fiber with quick release functionality
Monopod -option locking casters	Monopod -option locking casters. optional integrated locking casters for Monopod minimize danger to tip over, only for flat surfaces

dAV-Rmrr 19″ (LP)	dAV-Rmrr 19″ (LP). digital switch matrix in 19″ rack mount
dAV-Rmrr 19″	dAV-Rmrr 19″. digital switch matrix in 19″ rack mount
dAV-Rmrr base 19″	dAV-Rmrr base 19″. switch matrix digital receiver base unit dAV-Rmrr (without inputs and outputs, need to be added) able to receive and switch stereo audio and video signals from dAV-C(r) and dAV-Cr-HD, and other inputs to various selectable outputs 2 additional 3,5mm audio outputs included to switch separately; OSD functionality, camera remote software and Ethernet remote integrated 19″ (4HU) rack mount, 20×20 switch matrix (new, configurable integrated LCD displays settings); 2 integrated loudspeakers; remote control buttons for cameras; documentation available options: remote table top interface; external loudspeaker	1
dAV-R option – cominterface	dAV-R option -cominterface interface card to connect external equipment: dAV-R option -OSD: on screen display dAV-R option -ccs: camera control software (allows firmware updates, remote control and debugging via USB connection) dAV-Rrc-Joy: RS485 connection for external table top joystick remote	1
dAV-R option -Ethernet	dAV-R option -Ethernet remote additional Ethernet interface card for option -cominterface to control all integrated receiver remote functions up to 8 control connections at the same time possible (ccs, OSD,..)	1
dAV-Rmrr option -ccs	dAV-Rmrr option -ccs. camera control software option for all camera and pan/tilt functions additional controlling of switch matrix settings executable software to be run e.g. from a documentation-PC (dAV-R option -r and dAV-R option -cominterface necessary to run this function)	1
dAV-R option -OSD	dAV-R option -OSD. OSD function for dAV-R(r)-SD und dAV-Rr-HD. function: on screen display integratable in video stream e.g. frequency and field strength, time, date and DUT number (depending on your RF control software). Driver programming details included in manual NEW: with integrated battery and configurable (time display) real time clock to permanent display date/time without being connected to a PC	1
PS120-5-2f	PS120-5-2f. external power supply (not for use inside ALC during EMC-tests!) input: 100 .. 240VAC; 50 .. 60Hz; output: 12V/5A connector: 2-pole female AC-plug: Type C – Europe (Standard, Type A (US) or G (UK) avbl. STATE IN PO!)	1

dAV-Rmrr-HD OI-DO (LP)	dAV-Rmrr-HD OI-DO (LP). digital optical HD input/output board for dAV-Rr-HD; optical In and digital Out for switch matrix integrated on one PCB board, separately controllable via switch matrix
optoFlex information

optoFlex-s	Pos. 1: optoFlex-NT, new technology optical Flexray link with one duplex optical fiber – hardware identical to
	Pos. 2: optoFlex-s, optical Flexray link with two duplex optical fibers – hardware identical to optoFlex-NT
	Pos. 3-6: 1-8 channel analog link with 100kHz bandwidth. Scale Pos. 4,5 and 6 to 1-8
	Pos. 3: Ux/14 base unit -BNC, 1 to 8 (16) channel analog link each with 100kHz bandwidth – shielded receiver
	– channels and filters added separately
	Pos. 4: Ux/14-channel -BNC Pos. 5: FI-1-100k-BNC
	Pos. 6: FO-FB-BNC
	Pos. 7-10: 1-8 channel analog link with 1MHz bandwidth. Scale Pos. 8,9 and 10 to 1-8
	Pos. 7: Ux/12-1M base unit, 1 to 8 channel analog link each with 1MHz bandwidth – table top receiver version
	(also as shield version available – same price) – channels and filters added separately
	Pos. 8: Ux/12-1M-channel
	Pos. 9: FI-1-1M-BNC
	Pos. 10: FO-FB-BNC
	optoFlex-NT
optoFlex-NT	optical link for FlexRay-signals (bidirectional) with up to 10Mbit/s. separate transmission of diverse signals (to avoid timing issues)	1
	Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS75-5m (standard non shielded wall plug power supply to be used outside ALC
optoFlex-NT Transceiver	optical transceiver for FlexRay signals FlexRay-interface: max. 10MBit/s separate transmission of control signals FlexRay-transceiver: TJA1081BTS (others on request) FlexRay choke: B82789C0104, 100uH (others on request) FlexRay-connectors: SUB-D9 female optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation available option: 19″ rack mount (for up to 10 automotive links in 2HU)	1
Ux/14 Receiver base unit -BNC	digital optical receiver for analog signals from Ux/14 transmitter output voltage: +/- 15V optical connector: FSMA electrical connector: up to 8x (16x) BNC shielded metal housing with integrated NiMH batteries, 5-pole charge plug	1
LWL-S 20m	duplex optical fiber (62,5/125µm), length 20m, FSMA-FSMA	1
CH-1-5m	standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	2
external Felxray-Protector termination 100Ohm (metal	to be used for EMS/EME-testing. metal housing with connection plate enables GND connection if wanted/needed	1
optoFlex-s
optoFlex-s	optical link for FlexRay-signals (bidirectional) with up to 10Mbit/s. Separate transmission of diverse signals (to avoid timing issues)	1
	Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable)
optoFlex-s Transceiver	optical transceiver for FlexRay signals FlexRay-interface: max. 10MBit/s FlexRay-transceiver: TJA1081BTS (others on request) FlexRay choke: B82789C0104, 100uH (others on request) FlexRay-connectors: SUB-D9 female optical connector: 2x duplex FSMA (one additional fiber used to avoid timing issues) shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation available option: 19″ rack mount (for up to 10 automotive links in 2HU)	2
LWL-S 20m	duplex optical fiber (62,5/125µm), length 20m, FSMA-FSMA	2
CH-1-5m	standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	2
external Felxray-Protector termination 100Ohm (metal	to be used for EMS/EME-testing. metal housing with connection plate enables GND connection if wanted/needed	1
Ux/14 base unit – BNC	digital optical transmission of analog signals (base unit)
Ux/14 base unit – BNC	1 up to 8 (or up to 16 with «Ux/14 base unit -BNC extension) analog channels «U16/14-channel -BNC» integratable, resolution min. 10Bit, min. accuracy 1% of p-p value, bandwidth max. 100kHz (-3dB) For signal transmission (ALC => CR): input filters for transmitter necessary For opposite direction of signal transmission (CR => ALC – to stimulate DUT): output filters for receiver needed. Output filters do improve signal quality (noise reduction), so it is recommended to use output filters too.	1
	Optional available external power supplies – prices on request: BP60-5f (4Ah shielded battery pack to power optical device inside ALC) OR BP60-5f/10Ah (10Ah shielded battery pack to power optical device inside ALC) SC-30-5m5m (shielded connection cable) PS75-5m (standard non shielded wall plug power supply to be used outside ALC)
optoFlex-NT Transceiver	optical transceiver for FlexRay signals FlexRay-interface: max. 10MBit/s separate transmission of control signals FlexRay-transceiver: TJA1081BTS (others on request) FlexRay choke: B82789C0104, 100uH (others on request) FlexRay-connectors: SUB-D9 female optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation available option: 19″ rack mount (for up to 10 automotive links in 2HU)	2
LWL-S 20m	duplex optical fiber (62,5/125µm), length 20m, FSMA-FSMA	1
CH-1-5m	standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	2
external Felxray-Protector termination 100Ohm (metal	to be used for EMS/EME-testing. metal housing with connection plate enables GND connection if wanted/needed	1
Ux/14-channel -BNC	analog BNC channel for Ux/14 base unit -BNC ; up to 8 (or 16 with add on) channels integratable; add external filter FI-1-100k-BNC separately!	1
FI-1-100k-BNC	external input filter to be used for EMS/EME-testing with Ux/12-1M (BNC) connectors: BNC cut off frequency (-3dB): 100kHz division ratio: 1:1	1
FO-FB-BNC	external output filter applicable for analog transmission links (Ux/12, Ux/14 etc.) with BNC output connector. needs to be connected to the output of the receiver, if a stimulus is supposed to be sent to the inside of the ALC (receiver located in ALC, transmitter located in CR). setup with ferrite bead reduces overshoots of rectangular signals.	1
Ux/12-1M Base Unit	digital optical transmission of analog signals 1 .. 8 channels type «Ux/12-1M channel» integratable, resolution min. 10bit, min. accuracy 1% of full range, bandwidth max. 1MHz (-3dB); external battery pack for transmitter to extend system runtime	1
Ux/12-1M Transmitter base unit	input voltage +/- 15V; external filters/voltage dividers connectors: BNC optical connector: FSMA shielded metal housing with integrated NiMH batteries, 5-pole female charge plug, documentation	1
Ux/12-1M Receiver base unit	output voltage +/- 15V connectors: BNC optical connector: FSMA plastic table top housing , 2-pole female power supply plug (shielded metal housing with integrated batteries on request) AC-plug: Type C – Europe (Standard, Type A (US) or G (UK) avbl. STATE IN PO!)	1
CH-1-5m	standard plug-in charger (e.g. Friwo or Ansmann) number of cells: 4 .. 10 NiMH/NiCd cells up to 5Ah AC-input: 100-240V charge current: 600-800mA charge connector: 5 pole male AC-plug: Type C – Europe (Standard, Type A (US), G (UK) or I (AUS) avbl. STATE IN PO!)	1
BP84-5f	8,4V NiMH battery pack, capacity 4Ah in shielded metal housing with rubber protectors; suitable for optoUSB, U8/12-1M and others, 5 pole female charge plug without shielded cable, needs to be added separately	1
SC-30-5m5m	Shielded cable with folding ferrites. To be used with battery packs BPxx or shielded power supplies SPSxx to power devices during EMC-tests Length: 30cm Connectors: Binder series, male 5-pole – male 5-pole	1
PS120-2f	external power supply (only for CR use; not for use inside ALC during EMC-tests!) input: 100 .. 240VAC; 50 .. 60Hz; output: 12V/xA (adjusted to necessary value) connector: 2-pole female AC-plug: Type C – Europe (Standard, Type A (US) or G (UK) avbl. STATE IN PO!)	1
LWL-1 20m	simplex optical fiber (62,5/125μm), length 20m, FSMA-FSMA	1
Ux/12-1M-channel	analog channel for Ux/12-1M; up to 8 channels integratable; external filter FI-1-1M-BNC needs to be added separately add up to 8x	1
FI-1-1M-BNC	external input filter to be used for EMS/EME-testing with Ux/14-1M or U2/12 connectors: BNC cutoff frequency (-3dB): 1MHz division ratio: 1:1	1
FO-FB-BNC	external output filter applicable for analog transmission links (Ux/12, Ux/14 etc.) with BNC output connector. needs to be connected to the output of the receiver, if a stimulus is supposed to be sent to the inside of the ALC (receiver located in ALC, transmitter located in CR). setup with ferrite bead reduces overshoots of rectangular signals.	1

dAV-Rmrr-OI-HD/SD	dAV-Rmrr-OI-HD/SD. optical HD input channel for dAV-Rmrr base unit connect dAV-Cr-HD or dAV-Cr-SD to switch matrix optical connector: FSMA	1
dAV-Rmrr-DO VGA/DVI	dAV-Rmrr-DO VGA/DVI. digital output channel for dAV-Rmrr base unit connect one or two Standard TFT screens to switch matrix output connectors: – VGA and DVI-D via adapter cradle or DVI-D direct, 16:9 1080p, use standard Full-HD TFT screen – CVBS 4:3 PAL (reduced quality for cheap recording possibilities) – audio via 3,5mm plug 3GSDI output optional available	1
DVI-HDMI cable 2m	DVI-HDMI cable 2m. DVI-HDMI cable to connect receiver output to monitor with integrated audio length: 2m	1

WCM40	The wall mount WCM40 can be fixed to the walls with the help of screws. On the upper level a camera with pan/tilt unit can be placed, on the lower level e.g. the loudspeaker of our intercom system dAV-TRX-PS.
SPS120-5f	linear controlled shielded external power supply, applicable for use with dAV-Cr input: 220 .. 240VAC; 50 .. 60Hz output: 12V/1A 5-pole female connection plug 110V available on request -> STATE IN PO power supply cable for 230V or 110V application, length approx. 1.8m AC-plug: Type F – Europe (Standard, Type B (US) or G (UK) avbl. STATE IN PO!) without shielded cable, needs to be added separately
OSD
Ethernet Port
Camera Control Software
HiRF Option	With the option -HiRF, camera and pan/tilt unit are fit for very high field strengths and frequencies. The devices are equipped with additional screws and special cables for a high immunity: >> 600V/m up to 40GHz.
Pan/Tilt	Include is a double shielded cable for connection to the P/T or battery pack.

MK - MESSTECHNIK PRODUCT LINE

RELIANT EMC PRODUCT LINES

MANUFACTURERS

Request a Quote / Contact Us!

MK-MESSTECHNIK Price List

qty

• Data Sheets

• Product Catalog