|
|
|
Antenna Holders / Baluns
|
VHA 9103 B
|
Holder / Balun without telescopic dipole elements (for use with Biconical BBA 9106, BBAL 9136, BBAK 9137, BBVK 9138)
|
HFBA 9122
|
HF-VHF Broadband balun / holder (0.1) 0.15 – 300 (500) MHz especially to measure very high field strength. BBAL 9136, BBA 9106, BBAK 9137, BBVU 9135 or BBUK 9139 biconical elements required.
|
VHBA 9123
|
Antenna Holder / Balun for Bicon. Broad Band Antenna (e.g. BBA), 50 / 200 W, (better antenna factor below 50 MHz, also EMV application 100 W
|
VHBB 9124
|
Antenna holder / balun 50:200 Ohm , high symmetry, 25-300 MHz, 10 W for BBA, BBAL, BBAK, BBVK
|
VHBC 9133
|
Antenna holder / balun 50:200 Ohm, 1 kW, for biconical or collapsible elements (BBA, BBAL, BBFA, Triangle, FBAA, FBAB)
|
VHBD 9134
|
High power antenna holder / balun 50:200, 2.5 kW, 20-200 MHz for biconical or collapsible elements BBFA 9146, N-connector
|
Opt. 7/16
|
Option: 7/16 connector
|
VHBD 9134-4
|
4 kW high power antenna holder / balun 50:200 W, 20-200 MHz for BBAL 9136 or BBFA 9146, 7/16-female connector.
|
UBAA 9114
|
Broadband Balun/Holder 4:1, 30-1000 MHz, 5 W, low loss, BBVU, BBUK, BAOC or BBOC elem. required
|
UBAA 9115
|
Broadband Balun/Holder 4:1, 30-1000 MHz, 5 W, extremely high symmetry, BBVU, BBUK, BAOC or BBOC elem. required
|
|
|
Biconical elements
|
BBA 9106
|
Biconical Elements, 30-300 MHz, requires VHA 9103 B, VHBC, VHBB or VHBA
|
BBAL 9136
|
Biconical Elements, 20-200 MHz, requires VHA 9103 B, VHBC, VHBB or VHBA
|
BBAK 9137
|
Biconical Elements, 45-450 MHz broad band, requires VHA 9103, VHBB or VHBA
|
BBVK 9138
|
Biconical Elements, 60-600 MHz broad band, requires VHA 9103, VHBB or VHBA
|
BBVU 9135
|
Biconical Elements, (30)100-1000 MHz (like VUBA), for UBAA 9114/9115
|
BBUK 9139
|
Biconical Elements, 160-1200 MHz broad band (like UBA), for UBAA 9114/9115
|
|
|
Collapsible or open Biconical Elements
|
BBAE 9179
|
Foldable elements for immunity for automotive applications, optimized for 1 m measurement distance, max. diameter 150 cm, 20-220 MHz suitable for: VHBC 9133, VHBD 9134, VHBD 9134-4. Some «aluns may need a mechanical modification!
|
Holder Short
|
Plastic holders to be fixed at a high power balun e.g. VHBA 9123, VHBC 9133, VHBD 9134, VHBD 9134-4. BBAE 9179 elements have 2 pins. The HOLDER SHORT accept the second pin and absorb the torque caused by BBAE 9179 in horizontal Polarization.
|
BBFA 9146
|
Large collapsible aluminum Elements with extensions up to 4 m
|
FBAB 9177
|
Collapsible Biconical Elements 30 – 300 MHz (instead of BBA)
|
FBAL 9178
|
Large Collapsible Biconical Elements 20 – 200 MHz (instead of BBAL)
|
BAOC 9216
|
Open Conical Elements, 160-1200 MHz broad band, for UBAA 9114/9115
|
BBOC 9217
|
Open Conical Elements, (30)100-1000 MHz broad band, for UBAA 9114/9115
|
|
|
Logarithmic Periodic Broadband Antennas
|
UHALP 9108 A
|
Log.-Periodic Antenna, alum. Tubing, 250 – 2400 MHz, low loss, 1 kW power
|
VUSLP 9111-1000
|
Log.-Per. Antenna, aluminum tubing, 1000 – 3000 (4000) MHz, low loss, 1 kW.
|
VUSLP 9111-400
|
Log.-Periodic Antenna, alum. Tubing, 400 – 3000 (4000) MHz, low loss, 1 kW .
|
VUSLP 9111
|
Log.-Periodic Antenna, alum. Tubing, 200 – 2300 (4000) MHz, low loss, 1 kW power
|
VUSLP 9111B
|
Log.-Periodic Antenna, alum. Tubing, (180) 200 – 3000 (4000) MHz, low loss, 1 kW power
|
VUSLP 9111E
|
Log.-Per. Antenna, aluminum tubing, 1 kW power, 70 (65)-3000 (4000) MHz. Recommended adapter: KG 9201. EN 61000-4-3
|
VULP 9118 A
|
Log.-Per. Antenna, aluminum tubing, 1 kW power, 180 -1500 (2000) MHz
|
VULP 9118 B
|
Log.-Per. Antenna, aluminum tubing, 1 kW power, 160-1500 (2000) MHz
|
VULP 9118 C
|
Log.-Per. Antenna, aluminum tubing, 1 kW power, 100-1400 (2000) MHz
|
VULP 9118 D
|
Log.-Per. Antenna, aluminum tubing, 1 kW power, (80) 95 -1500 (1800) MHz
|
VULP 9118 E
|
Log.-Per. Antenna, aluminum tubing, 1 kW power, 75 (50)-1500 MHz.
|
VULP 9118 E High Power
|
Log.-Per. Antenna, aluminum tubing, high power, 7/16-connector, 75 (50)-1500 MHz.
|
VULP 9118 F
|
Log.-Per. Antenna, aluminum tubing, end discs, 1 kW power, 55 -1800 MHz
|
VULP 9118 G
|
Log.-Per. Antenna, aluminum tubing, end discs, 1 kW power, 45 -1500 MHz
|
VULP 9118 D/E/F/G Special
|
Nearly identical gain as VULP 9118 D/E/F/G but with reduced width. Extra charge added to the basic model. Special = folded longest elements
|
VULP 9118 H
|
Log.-Per. Antenna, aluminum tubing, 1 kW power, (26) 30 – 1500 (1800) MHz, N- connector gain 6 dBi, VSWR<3, width 5.2 m, length 4.8 m, weight 35 kg.
|
Opt. WP
|
Option: Grey coating and sealing for outdoor use
|
USLP 9142
|
UHF – SHF Log. – Per. Antenna, 0.7 – 5 (8) GHz
|
USLP 9143
|
UHF – SHF Log. – Per. Antenna, (0.25) 0.3 – 7 (8) GHz
|
USLP 9143 B
|
UHF – SHF Log. – Per. Antenna, (0.18) 0.2 – 7 (8) GHz
|
ESLP 9145
|
UHF – EHF Log. – Per. Antenna, (0.7) 1- 18 (20) GHz, N-connector
|
XSLP 9142
|
Dual Polarized UHF-SHF Log.-Per. Antenna, 800 MHz – 3(5) GHz, 50 W
|
XSLP 9143
|
Dual Polarized UHF-SHF Log.-Per. Antenna, 300 MHz – 3(5.5) GHz, 50 W
|
|
|
Stacked Logarithmic Periodic Broadband Antennas
|
STLP 9128 C
|
Stacked double Log.-Per. Antenna, type gain: 9 dBi, alum. Tubing, high power, (150) 200 – 1500 (4000) MHz, N-connector 1 kW
|
Opt. 7/16
|
Option: with 7/16-connector 3 kW
|
Opt. 13-30
|
Option: with 13-30-connector limited to 2500 MHz but higher power up to 8 kW including adapter similar to AA 9202
|
STLP 9128 D
|
Stacked double Log.-Per. Antenna, type gain: 9 dBi, alum. Tubing, high power, 80 -3000 (4000) MHz, N-connector, fastlinks for quick removal of the rear parts of the antenna. Recommended Adapter: AA 9209
|
Opt. 7/16
|
Option: with 7/16-connector 3 kW
|
STLP 9128 D Special
|
Like STLP 9128 D but with folded longest elements and smaller structure angle, fastlinks. Antenna diameter < 150 cm. Recommended Adapter: AA 9209
|
Opt. 7/16
|
Option: with 7/16-connector 3 kW
|
STLP 9128 E
|
Stacked double Log.-Per. Antenna, type gain: 9 dBi, alum. Tubing, high power, (65) 80 -1500 (3000) MHz, N-connector 1 kW, fastlinks for quick removal of the rear parts of the antenna. Recommended Adapter: AA 9209
|
Opt. 7/16
|
Option: with 7/16-connector 3 kW
|
STLP 9128 E Special
|
Like STLP 9128 E but with folded longest elements and smaller structure angle. Antenna diameter < 150 cm. Fastlinks for quick removal of the rear parts of the antenna. Recommended Adapter: AA 9209
|
Opt. 7/16
|
Option: with 7/16-connector 3 kW
|
STLP 9148
|
Stacked double Log.-Per. Antenna, type gain: 9 dBi (0.7) 1 – 18 (20) GHz, N- connector
|
STLP 9149
|
Stacked double Log.-Per. Antenna for IEC 61000-4-3 type gain 10.3 dBi, (0,6) 0,7 – 9 (10,5) GHz, N-connector female.
|
STLP 100-500
|
Stacked double Log.-Per. Antenna, type Gain: 11 dBi, alum. Tubing, high power, (75) 100 – 500 (550) MHz, 13/30 (f)-connector 5 kW, dimensions: 166x178x402 cm, 52 kg
|
|
|
Biconic Logarithmic Periodic Antennas (Hybrid)
|
VULB 9160
|
TRILOG Super Broadband test Antenna, (25) 30 – 1000 (1700) MHz, 10 W
|
VULB 9161
|
TRILOG Super Broadband test Antenna, 30 – 1000 (2000) MHz, 1 kW
|
VULB 9161 SE
|
TRILOG Super Broadband test Antenna, 30 – 1000 (2000) MHz, 1 kW with short Triangle elements, diameter < 150 cm
|
VULB 9162
|
TRILOG Broadband Antenna 30 MHz – 7 GHz, 100 W, diameter < 150 cm
|
VULB 9163
|
TRILOG Super Broadband test Antenna, (25) 30 – 3000 (4000) MHz, 100 W (200 W)
|
VULB 9168
|
TRILOG Super Broadband Test Antenna, (25) 30-1000 (2000) MHz, 10 W, reduced width, diameter < 1.5 m.
|
Opt. Triext.
|
Option for VULB 9163, VULB 9161, VULB 9161 SE: angled Triangle Extensions to increase the gain by type 6 dB below 70 MHz.
|
|
|
Biconical Antennas
|
SBA 9113 B
|
Small Biconical Antenna 80 MHz – 3 GHz for harmonics measurements according To IEC61000-4-3.
|
SBA 9113
|
Small biconical microwave antenna 0.5 – 3 GHz, 20 W. CIS/A/648/CDV CISPR 16-1-4 Site evaluation above 1 GHz
|
SBA 9112
|
Small biconical microwave antenna (1) 3 – 18 GHz, 10 W including transport case. CIS/A/648/CDV CISPR 16-1-4 Site evaluation above 1 GHz
|
SBA 9119
|
Small biconical microwave antenna 1 – 6 GHz, 20 W. CIS/A/648/CDV CISPR 16-1-4 Site evaluation above 1 GHz including transport case.
|
UBA 9116
|
Biconical UHF broad band antenna (160) 300 -1000 (1100) MHz
|
VUBA 9117
|
Biconical VHF-UHF broad band antenna (30) 150 -1000 MHz
|
|
|
Dipoles
|
VHA 9103
|
VHF Half-Wave Dipole with 2 sets of telescopic elements, 30-300 MHz
|
UHA 9105
|
Tunable UHF – Half – Wave Dipole, 300 – 1000 MHz w. telescopic elements
|
UHA 9125 C
|
Tunable UHF – Half – Wave Dipole with EMI – Balun, 0.75 – 2 GHz with 4 sets of elements, LE = 180, 140, 100, 80 mm including transport case.
|
UHA 9125 D
|
Tunable UHF – Half – Wave Dipole with EMI – Balun, 1.0 – 3 (4) GHz with 6 sets of elements, LE = 140, 114, 90, 72, 60, 48 mm, including transport case.
|
|
|
Precision Dipoles
|
VHAP
|
VHF Precision Dipole 30-300 MHz, 2 sets of telescopic elements (mostly required in pairs) CISPR 16-1-5.
|
UHAP
|
UHF Precision Dipole 300-1000 MHz (VHAP & UHAP mostly required in pairs) CISPR 16-1-5
|
CCA
|
Carrying and storing case for 2 x VHAP or 2 x UHAP, cases for other antennas also available.
|
VHAPA
|
Calibration adapter for VHAP Precision Dipoles
|
UHAPA
|
Calibration adapter for UHAP Precision Dipoles
|
|
|
Monitoring & drive testing antennas
|
ILS Dipole
|
Linear polarized half-wave dipole with 1:1 balun and fixed element length for field strength measurements at instrument landing systems (ILS) 108 – 118 MHz and 320 – 340 MHz.
|
CCA ILS
|
Transport and storage case made of aluminum for ILS Dipole
|
FT 01 S
|
FM broadcast and TV bands antenna, detachable, 47 – 860 (1000) MHz, high directivity
|
FT 01 UKW
|
Additional elements for enhanced FM broadcast directivity
|
RSH 2342
|
Omni directional horizontally polarized UHF antenna 170 – 350 MHz.
|
RSH 4786
|
Omni directional horizontally polarized UHF antenna (350) 470 – 860 (1050) MHz for outside use.
|
RS 16
|
Vertical polarized microwave biconical antenna (0,5) 1 – 6 (8,5) GHz with omni directional H-plane pattern.
|
RE 1790
|
Vertical polarized VHF- UHF biconical antenna (170) 230 – 1000 (1100) MHz with omni directional H-plane pattern.
|
RE 4590
|
Vertical polarized VHF- UHF biconical antenna (330) 450 – 1000 (1100) MHz with omni directional H-plane pattern.
|
RS 0460
|
Vertically polarized symmetrical biconical antenna 0,4 – 6 GHz, Omni directional in the H-plane.
|
CCA RS 0460
|
Transport case for RS 0460.
|
|
|
Broadband Horn Antennas
|
BBHA 9120 A
|
Broad-Band Horn Antenna (0.8) 1 – 5 (10) GHz, N-connector
|
BBHA 9120 B
|
Broad-Band Horn Antenna 1 – 10 GHz, N-connector
|
BBHA 9120 C
|
Broad-Band Horn Antenna 2 – 18 (20) GHz, SMA connector
|
BBHA 9120 D
|
Broad-Band Horn Antenna (0,8) 1 – 18 GHz, N-connector
|
BBHA 9120 E
|
Broad-Band Horn Antenna 0.5 – 6 GHz, N-connector
|
BBHA 9120 F
|
Broad-Band Horn Antenna 0.2 – 2 GHz, N-connector
|
Opt. 7/16
|
Option: with 7/16-connector 3 kW
|
BBHA 9120 F Opt. 1 m
|
Very short telescopic tube to be inserted into the steel foot of AM 9144 to set BBHA 9120 F to a height of 1 m referring to the antenna center in both polarizations.
|
BBHA 9120 G
|
Broad-Band Horn Antenna 0.4 – 2.8 GHz, 7/16-connector
|
BBHA 9120 LF
|
Broad-Band Horn Antenna 0.7 – 6 GHz, N-connector
|
BBHA 9170
|
Broad-Band Horn Antenna 15 – 26.5 (40) GHz, SMA compatible connector
|
HA 9250-24
|
Pyramidal standard gain horn Antenna, 2 – 4 GHz, 7/16-connector, 20 dBi, optimized for far field gain.
|
HA 9250-48
|
Pyramidal standard gain horn Antenna, 4 – 8 GHz, 7/16-connector, 20 dBi, optimized for far field gain.
|
HA 9251-12
|
Pyramidal standard gain horn Antenna, 1-2 GHz, 7/16-connector, far field gain 19-22 dBi, optimized for 1 m gain.
|
HA 9251-24
|
Pyramidal standard gain horn Antenna, 2 – 4 GHz, 7/16-connector, 18 dBi, optimized for the gain in 1 m distance.
|
HA 9251-48
|
Pyramidal standard gain horn Antenna, 4 – 8 GHz, 7/16-connector, 19 dBi, optimized for the gain in 1 m distance.
|
HWRD750
|
Double ridged horn antenna 7.5-18 GHz with waveguide flange WRD750. Gain 16-21 dBi, 1 kW, especially to generate very high field strengths.
|
|
|
Dual polarized horn antennas
|
CTIA 0710
|
CTIA horn antenna, dual polarized, 0,7-10 GHz, type 30 dB cross polar rejection, antenna with reduced size for OTA measurements. Antenna without 22 mm tube!
|
Opt. CTIA tube 22 mm
|
Option for CTIA 0710: 22 mm tube with indexing ring.
|
BBHX 9120 E
|
Dual polarized Broad-Band Horn Antenna 0.4 – 10 GHz, N-connectors
|
BBHX 9120 LF
|
Dual polarized Broad-Band Horn Antenna (0.8) 1 – 8 (10.5) GHz, N-connectors
|
|
|
Standard Gain Antennas
|
SGA
|
Standard Gain Antennas, type 9.8 dBi gain, 60° pattern, accurately calibrated (2 half-wave dipoles in front of a l x l reflector, design frequencies approx. 400-2800 MHz.
|
|
|
Standard Gain Antennas
|
SGA…
|
Standard Gain Antennas, type 9.8 dBi gain, 60° pattern, accurately calibrated (2 half-wave dipoles in front of a l x l reflector, design frequencies approx. 400-2800 MHz.
|
|
|
Active Antennas
|
VAMP 9243
|
Vertical active rod antenna, 9 kHz – 30 MHz, BNC, reduced noise floor, with mounting nut for AM 9144 and rechargeable battery.
|
Opt. GP
|
Option: Aluminum Ground plane, 0.6 x 0.6 m
|
Opt. ACS 410
|
Option: Charger ACS 410
|
Opt. Divider
|
Option 20 dB plug in divider to measure high field strength
|
Opt. CA 9243
|
Calibration Adapter for VAMP 9243
|
Opt. MIL461F bonding kit
|
Bonding kit for VAMP 9243 according MIL-STD-461F consisting of a BNC cable double shielded ca. 70 cm, with braid current blocking ferrite in the center, elbow aluminum angle with BNC bulkhead adapter.
|
EFS 9218
|
Active Electric Field Probe with Biconical Elements, 9 kHz – 300 MHz, 12 µV/m – 65 V/m, antenna factor switchable 46 dB/m or 20 dB/m, high symmetry, built in rechargeable battery
|
Opt. ACS 410
|
Option: Automatic charger ACS 410 for EFS 9218
|
EFS 9219
|
Active antenna holder, high sensitivity (1 µV/m … 3 V/m), 9 kHz-30 MHz, BBUK 9139 biconical elements required.
|
Opt. Tube
|
Option: Isolating tube with braid chokes for EFS 9219
|
Opt. ACS 410
|
Option: Automatic charger Ansmann ACS 410 for EFS 9219
|
|
|
Field probes
|
FSH3D
|
Isotropic H-Field Antenna for the Rohde under Schwarz hand held spectrum analyzer FSH or the TS-EMF System 9 kHz – 200 (300) MHz. Light weight low attenuation radom, outer diameter ca. 150 mm. The selection of the active loop and the power supply for the antenna is provided by the included short cable that can directly be connected to the R&S FSH.
|
FSHPH
|
Passive H-Field probe for hand held spectrum analyzers to measure large magnetic fields to analyze health effects of non-ionizing radiation according to standards like BGV-B11, ICNIRP, IEEE C95.1, FCC 96-236.
|
FSHPE
|
Passive E-field probe for hand held spectrum analyzers to measure large electric fields to analyze health effects of non-ionizing radiation according to standards like BGV-B11, ICNIRP, IEEE C95.1, FCC 96-236.
|
|
|
Automotive antennas
|
NMHA 5L
|
Nissan and Renault antenna set to test immunity against handy transmitters according to Nissan specification 28401NDS02 [5] and RENAULT 36-00-808/L 2010 (combined set) consisting of normal mode helical antennas, dipoles counterpoise and transport case (see extra list)
|
VW TL 82166 2009-05 Antenna Set
|
Antenna set according to Volkswagen Specification VW TL 82166:2009-05 section 7.3 «antenna set for mobile radio testing using mobile portable radio units inside the vehicle.» The set consists of: NMHA 26.5, NMHA 27.5, NMHA 28.5, NMHA 29.5, NMHA 71, NMHA 77, NMHA 83.75, NMHA 151, NMHA 166, SBA 9113 mini version total length of the balun LH=20 cm without the small original biconical elements, 420 NJ, Spacer 50, VW metal case large with short 22 mm tube, VW metal case small with short 22 mm tube, MSS 9630, AD Nm BNCf, AD Nm Nm Case for all parts CCA VW.
|
420 NJ
|
Elements for radiated immunity caused by handy transmitters with SBA 9113 or SBA 9113 mini version for the Ford standard RI115.
|
Opt. Spacer 50
|
Spacer made of Polystyrene to set the 420 NJ test distance to 50 mm.
|
WAND0918
|
Wireless Immunity “Wand” Antenna according to Dell Specification „SYSTEM IMMUNITY TO WIRELESS GSM TEST REQUIREMENT” 800 MHz -2 GHz.
|
RS 9244
|
Radiating source for CISPR/D/391/CD (CIS/D/386/CD, CIS/D/388A/CC), consisting of a 500 mm brass rod with 4 mm diameter and 2 aluminum angles with N-connectors.
|
|
|
Passive Rod Antenna
|
VPMP 9241
|
Monopole according to CISPR/D/391/CD (CIS/D/386/CD, CIS/D/388A/CC), passive, 2 N-connectors, element fixture for rod, rod, aluminum housing and ground plane.
|
Opt. TLD 9241
|
Top loading disc for VPMP 9241 diameter < 12 cm.
|
VPMP 9242
|
Vertical passive rod antenna, 10 – 40 MHz, possible rods: FBAB 9177, FBAL 9178, BBA 9106, BBAL 9136 (have to be ordered extra)
|
Opt. GP
|
Option: Aluminum ground plane 0.6 x 0.6 m
|
|
|
Helical antennas
|
HLX 0810- LHCP
|
Helical antenna 800 – 1000 MHz, left circular polarization., gain 11 dBc, 22 mm tube, N-jack.
|
HLX 0810- RHCP
|
Helical antenna 800 – 1000 MHz, right circular polarization., gain 11 dBc, 22 mm tube, N-jack.
|
CLSA 0110L
|
Conical Log Spiral Antenna 1-10 GHz, type gain 2 dBi, N-connector, left threaded.
|
CLSA 0110R
|
Conical Log Spiral Antenna 1-10 GHz, type gain 2 dBi, N-connector, right threaded.
|
|
|
Passive Magnetic Antennas, TX-Loop Antennas
|
HFRA 5148
|
Circular transmitting loop antenna diam. 180 mm, 1 turn
|
HFRA 5149
|
Circular transmitting loop antenna 9 kHz – 30 MHz, diam. 500 mm including 50 Ohm 20 Watt termination, N-connectors.
|
HFRA 5152
|
Circular transmitting loop antenna diam. 250 mm, DC-3 MHz
|
HFRA 5153
|
Circular transmitting loop antenna diam. 180 mm, 0-20 (30) MHz, 5 W
|
HFRA 5154
|
Circular transmitting loop antenna diam. 100 mm, 0.1 – 30 MHz, Transformer 50 Ohm, 0.5 W
|
HFRA 5155
|
Circular Transmitting VHF – UHF loop antenna, diam. 50 mm,
|
HFRA 5156
|
Circular Transmitting Loop Antenna diam. 50 mm, 0-5 MHz, 2 W, 10 turns
|
HFRA 5157
|
Circular Transmitting Loop Antenna diam. 50 mm, 0-20(30) MHz, 3 W, 2 turns
|
HFRA 5158
|
Circular Transmitting Loop Antenna diam. 180 mm, 0-2 MHz, 5 W, 10 turns
|
HFRA 5159
|
Circular Transmitting Loop Antenna diam. 250 mm, 0-400 kHz, 5 W
|
HFRA 5170
|
Cal. Loop 3 W, diam. 100 mm, 0-30 MHz, 1 turn, 250 Ohm
|
HFRA SF02G
|
Tunable resonant magnetic loop antenna to generate extremely high magnetic fields in the range 10 kHz to 30 MHz according to VG95373-13:2008-11 and VG95373-23:2008-11. Including sensor loop HFRAE 5163 under control cable.
|
|
|
Passive Magnetic Antennas, RX-Loop Antennas
|
HFRAE 5160
|
Receiving VHF – UHF loop antenna, diam. 50 mm, 2-300 MHz, transformer
|
HFRAE 5161
|
HF RX Loop, diam. 100 mm, 70 k-120 MHz, 1 turn, transformer
|
HFRAE 5162
|
VLF-HF RX Loop, diam. 250 mm, 50 k-30 MHz, 1 turn, transformer
|
HFRAE 5163
|
Passive magnetic loop antenna 9 kHz – 300 MHz, 1 turn, transformer, diam. 50 mm
|
|
|
CISPR 15 3-dimensional loop Antenna Van Veen
|
HXYZ 9170
|
3-dimensional large loop antenna, diam. 2 m, according EN 55015 / CISPR 15, Socket and Coaxial switch recommended
|
Socket for HXYZ 9170
|
Socket and mounting equipment for large loop HXYZ 9170
|
Coaxial Switch for HXYZ 9170
|
3 in one coaxial switch for manual / remote operation including cable set (3 BNC cables with braid current blockers) for large loop HXYZ 9170
|
HFCD 9171
|
Calibration Balun / Dipole for HXYZ 9170 (recommended accessory: AM 9144)
|
CDA 9271
|
Adapter to hold HFCD 9171 on AM 9144, 3/8’’ female large camera thread.
|
|
|
Active Loop Antennas / Magnetic Field Probes
|
FMZB 1513
|
Active loop antenna, 9 kHz to 30 MHz, constant antenna factor 20 dB/m with built in NiMH batteries, detachable glass fiber handle 180 mm. Optimized for mobility.
|
Opt. ACS 110
|
Option: Charger ACS 110 for FMZB 1513.
|
Opt. 500 mm Handle
|
Option for FMZB 1513: Additional glass fiber handle of 500 mm length.
|
CCA 1513
|
Transport case for FMZB 1513 and accessories.
|
FMZB 1519
|
Active magnetic loop antenna according to CISPR 16, 9 kHz to 30 MHz, constant antenna factor 20 dB/m, built in rechargeable battery, including charger for 230V
|
HMDA 1545
|
Hand held magnetic field meter, LCD, acoustic field strength indication with tone generator, 9 kHz- 50 (80) MHz, 200µA/m … 1 A/m, 6 x Type AA NiMH.
|
Opt. ACS 410
|
Option: ACS 410 charger for HMDA 1545
|
HFS 1546
|
Active magnetic Field Probe with shielded 50-mm-Loop, 150 kHz – 400 MHz
|
Opt. ACS 110
|
Option: ACS 110 charger for HFS 1546
|
FMZB 1512
|
Active magnetic loop antenna with 15 cm loop diameter for mobile applications with built in rechargeable batteries, 9 kHz to 30 MHz, antenna factor adjustable.
|
Opt. ACS 110
|
Option: ACS 110 charger for FMZB 1512
|
|
|
Helmholtz coils, electro magnets
|
MagTest System
|
Schwarzbeck Software to test Immunity against magnetic fields and to calibrate monitoring loops. Fulfills standards like MIL-461 E, ISO 11452-8, EN 61000-4-8, SAE J551-17 and others. Control of all required devices via GPIB.
|
SHUNT 9570
|
Low inductive precision high power shunt 0.25 and 1 Ohm 2 kW or 0.5 Ohm 1 kW respectively for best load matching at lower frequency end, cooling fans.
|
HHS 5201-6
|
Helmholtz Coils circular up to 2860 A/m 5 MHz for DuT size 45 mm.
|
HHS 5201-98
|
Helmholtz Coils circular up to 64 kA/m 200 kHz for DuT size 45 mm.
|
HHS 5203-20
|
Helmholtz Coils, circular, diam. 300 mm, 330 A/m for Calibration or Immunity
|
HHS 5204
|
Helmholtz Coils for Calibration purposes, circular, diam. 420 mm, 5 turns f. 60 A/m
|
HHS 5204-12
|
Helmholtz Coils, circular, diam. 400 mm, 2500 A/m 500 kHz MIL-STD 461E
|
HHS 5204-36
|
Helmholtz Coils, circular, diam. 400 mm, 2500 A/m 150 kHz MIL-STD 461E
|
HHS 5206-16
|
Circular pair of Helmholtz coils, diameter 600 mm, up to 2100 A/m, max. current 55 A.
|
HHS 5210
|
Helmholtz Coils up to 300 A/m constant H field, 1 m x 1 m, 10 turns per coil, EN 61000-4-8, VDE 0847 part 4-8
|
HHS 5210-100
|
Helmholtz Coils up to 2183 A/m constant H field, 1 m x 1 m, 100 turns per coil, EN 61000-4-8, VDE 0847 part 4-8
|
HHS 5212
|
Helmholtz Coils up to 250 A/m H field, 1.20m x 1.20 m, 10 turns.
|
HHS 5213-50
|
Helmholtz Coils 1.25 m x 1.25 m, 50 turns per coil, according EN 55103-2 A.2.1.b)
|
HHS 5213-100
|
Helmholtz Coils 1.29 m x 1.29 m, 100 turns per coil.
|
HHS 5215
|
Helmholtz Coils up to 200 A/m constant H field, 1,5 m x 1,5 m, 10 turns per coil
|
HHS 5215-100
|
Helmholtz Coils up to 2000 A/m constant H field, 1,5 m x 1,5 m, 100 turns per coil
|
HHS 5218
|
Helmholtz Coils up to 126 A/m constant H field, 1,8 m x 1,8 m, 10 turns per coil
|
HHS 5230-100
|
Pair of Helmholtz coils according to SAE J551-17: 2 square coils with a side length of 3 m, 100 turns, max. 650 A/m, each coil movable separately on a wheeled platform.
|
NFCN 9731-100
|
Matching network for HHS 5230-100 for the following frequencies: 16,666 Hz; 50 Hz; 60 Hz; 150 Hz; 180 Hz. Recommended amplifiers: 2 units of AE Techron 7224.
|
AGEM 5520
|
Air gap electromagnet for extreme high magnetic field strengths of up to 2.2 Tesla.
|
FESP 5132
|
Radiating loop diam. 12 cm, 20 turns, DC to 250 kHz, max 15 A, 2x Banana jack 4mm, ISO 11452-8, MIL-STD 461E p. 108, EN 55103 5.18.3.2
|
Opt. LoopHolder50
|
Calibration fixture to hold FESP 5134-40 in FESP 5132 in a distance of 50 mm according MIL461E figure RS101-3.
|
FESP 5134-40
|
Loop Sensor / Antenna, diam. 4 cm, 51 turns, 5 Hz to 250 kHz, electrostatic shielding, BNC jack.
|
FESP 5133
|
Loop Sensor / Antenna, 36 turns in 4 layers, diam. 133 mm, EN 55103-1 A.2.b), EN 55103-2 A.4.1 0 – 200 kHz, banana plugs (standard) or BNC connector female.
|
FESP 5133-7/41
|
Circular shielded loop sensor to determine the magnetic field strength 5 Hz – 250 kHz. 36 turns AWG 7/41, diameter 133 mm, distance gauge 7 cm included. MIL 461E RE101 or RS101 alternative test procedures.
|
FESP 5133
1330
|
Circular radiating loop for extremely high field strength up to several mT, 225 turns, according SF 01 G, VG95377.
|
FESP 5135
|
Radiating coil diam. 0.5 m, 20 turns in one layer, according EN 55103-2 A.3.1
|
RSAL 5340
|
LF 3-dimensional magnetic rolling stock antenna for the lower frequency range according to CLC/TS 50238-3:2010. 10 kHz to 100 kHz.
|
RSAH 5324
|
3-dimensional magnetic rolling stock antenna for the higher frequency range according to CLC/TS 50238-3:2010. 100 kHz to 1.3 MHz.
|
RSA COVER
|
Dirt and weather protection cover to house the rolling stock antennas RSAL 5340 or RSAH 5324 and to fix the antenna to the rail track.
|
|
|
Antenna Masts / Tripods / Adapters
|
AM 9104
|
Detachable Antenna Mast System (glass-fiber tubing) for VHF-UHF Antennas, manual height scanning 0.4 m to 4 m, insulated mast and antenna box with 0°/90° detents, zinc-plated / stainless steel 3-leg mast foot.
|
Opt. wheels
|
Option: Caster Wheels and Brakes for zinc-plated / stainless steel 3-leg mast foot
|
Opt. GF
|
Alternative Option: Non metallic (glass-epoxy) mast foot for AM 9104
|
AM 9144
|
Glass – Epoxy tube Antenna Mast System, height set by screw 1.2 – 2 m, 3/8” thread on top, zinc-plated / stainless steel 3-leg mast foot.
|
Opt. GF
|
Option: Non metallic (glass-epoxy) mast foot for AM 9144
|
Opt. wheels
|
Option: Caster Wheels and Brakes for 3-leg mast foot
|
Opt. short
|
Option: height set range from 0.90 – 1.60 m (shorter version)
|
AA 9202
|
Mast Adapter for AM 9144 with 22 mm hole for most Antenna models, 3/8” and 1/4” camera threads, polarization continuously adjustable.
|
AA 9202 POM
|
Non metallic mast adapter for most light weight Antenna models with 22 mm tube, minimizes reflections, 3/8” camera thread, polarization continuously adjustable.
|
AA 9203
|
Mast Adapter for AM 9144 with 22 mm hole for most Antenna models, 3/8” and 1/4” camera threads polarization and elevation continuously adjustable
|
AA 9205
|
Orthogonal Swivel Adapter for positioning in 3 perpendicular directions. Application: determination of the magnitude of the field strength
|
AA 9209
|
Antenna adapter to fix STLP 9128 E, STLP 9128 E special, STLP 9128 D, STLP 9128 D special on AM 9144. Allows antenna rotation without height adjustment. Antenna can be fixed in the center of gravity without any collision with the AM 9144 during polarization change.
|
AA 9213
|
Adapter to convert a 3/8’’ female thread to 22 mm tube, e.g. to fix BBHA 9170 on AM 9104.
|
RS 9214
|
Adapter to convert the R&S Aluminum Flange into 22 mm tube with indexing ring.
|
RA 9215
|
Indexing adapter for fast & precise polarization change.
|
R&S Flange
|
R&S Flange for Schwarzbeck antenna with 22 mm tube.
|
KG 9201
|
Mast Adapter (swivel, 90° vertical/horizontal polarization for AM 9144), for VULP 9118 D,E,F,G and VUSLP 9111 E only
|
PPS 9208
|
Pneumatic polarization shifter with 2-way pneumatic cylinder for all Schwarzbeck antennas with 22 mm tube on AM 9144. Compressed air required.
|
SWHA 9204
|
Swivel handle for light antennas
|
EA 9207
|
Adapter for Schwarzbeck antennas with 22 mm tube on EMCO mast.
|
TA 9204
|
Thread Adapter with 3/8″ female and 1/4″ male threads. Mainly for American antenna brands.
|
TA 9205
|
Thread Adapter with 1/4″ female and 3/8″ male threads. (For camera tripods, not for AM 9144)
|
TA 9206
|
Thread Adapter with 3/8″ female and 5/8″ male threads. (Geodesy)
|
POSITIONER
|
Positioner for light weight antennas like SBA 9113 with 420 NJ. The positioner consists of: 1 piece of glass fiber tube 22 mm thick, 1000 mm long, an adapter AA 9203 is mounted to the tube. The other end of the tube carries a 3/8 inch male camera thread.
|
|
|
LISN Line Impedance Stabilization Networks
|
NSLK 8127
|
V-LISN, 9 kHz – 30 MHz, 50 µH + 5 Ohm || 50 Ohm, 250 µH isolating choke can be shorted, 2 x 16 A Schuko socket, Artificial Hand.
|
Opt. RC
|
Option RC for LISN: Remote Control with built in power supply. LISN can be controlled by R&S or Schwarzbeck code, including remote control cable for your receiver type (Please specify your receiver type!). LISN can be selected from the R&S receiver menu or in the EMC32 software like an R&S LISN. No programming of the user interface necessary. Functions: path selection and PE grounded or via choke.
|
Opt. PLC
|
Option: Power Line Communication, according to EN 50065-1, selectable ranges: 3 – 9 kHz, 9 – 95 kHz, 95 kHz – 30 MHz.
|
NSLK 8126
|
V-LISN, 9 kHz – 30 MHz, 50 µH + 5 Ohm || 50 Ohm, 250 µH isolating choke can be shorted, 4 x 16/25 A, 2 x 16 A Schuko and 4 x 16 A CEKON socket, Artificial Hand.
|
Opt. RC
|
Option RC for LISN: Remote Control with built in power supply. LISN can be controlled by R&S or Schwarzbeck code, including remote control cable for your receiver type (Please specify your receiver type!). LISN can be selected from the R&S receiver menu or in the EMC32 software like an R&S LISN. No programming of the user interface necessary. Functions: path selection and PE grounded or via choke.
|
NSLK 8128
|
V-LISN, 9 kHz – 30 MHz, 50 µH + 5 Ohm || 50 Ohm, 250 µH isolating choke can be shorted, 4 x 32/50 A, 2 x 16 A Schuko and 4 x 32 A CEKON socket, Artificial Hand.
|
Opt. RC
|
Option RC for LISN: Remote Control with built in power supply. LISN can be controlled by R&S or Schwarzbeck code, including remote control cable for your receiver type (Please specify your receiver type!). LISN can be selected from the R&S receiver menu or in the EMC32 software like an R&S LISN. No programming of the user interface necessary. Functions: path selection and PE grounded or via choke.
|
NNLK 8121
|
V-LISN, 9 kHz – 30 MHz, 50 µH + 5 Ohm || 50 Ohm, 250 µH isolating choke, 4 x 50 (100) A, wing terminals (For continuously 100 A add the options cont. high current and cooling fans!)
|
Opt. RC
|
Option RC for LISN: Remote Control with built in power supply. LISN can be controlled by R&S or Schwarzbeck code, including remote control cable for your receiver type (Please specify your receiver type!). LISN can be selected from the R&S receiver menu or in the EMC32 software like an R&S LISN. No programming of the user interface necessary. Functions: path selection and PE grounded or via choke.
|
Opt. cont. high current
|
Option: cont. high current, additional terminals to bypass the 250 μH chokes, provides less voltage drop and less heating.
|
Opt. 400/700 V
|
Option: 400/700 V Voltage to Neutral / Voltage between lines
|
Opt. Fans
|
Option: Cooling Fans
|
NNLK 8129
|
V-LISN, (9) 150 kHz – 30 MHz, 50 µH || 50 Ohm, 4 x 200 (300) A, wing terminals, low voltage drop, High power resistors
|
Opt. 400/700 V
|
Option: 400/700 V Voltage to Neutral / Voltage between lines
|
Opt. RC
|
Option RC for LISN: Remote Control with built in power supply. LISN can be controlled by R&S or Schwarzbeck code, including remote control cable for your receiver type (Please specify your receiver type!). LISN can be selected from the R&S receiver menu or in the EMC32 software like an R&S LISN. No programming of the user interface necessary. Functions: path selection and PE grounded or via choke.
|
Opt. Fans
|
Option: Cooling Fans
|
NNLK 8130
|
V-LISN, (9) 150 kHz – 30 MHz, 50 µH || 50 Ohm, 4 x 400 (500) A, wing terminals, low voltage drop, High power resistors, cooling fans.
|
Opt. RC
|
Option RC for LISN: Remote Control with built in power supply. LISN can be controlled by R&S or Schwarzbeck code, including remote control cable for your receiver type (Please specify your receiver type!). LISN can be selected from the R&S receiver menu or in the EMC32 software like an R&S LISN. No programming of the user interface necessary. Functions: path selection and PE grounded or via choke.
|
Opt. 400/700 V
|
Option: 400/700 V Voltage to Neutral / Voltage between lines
|
NNLK 8140
|
Single Path V-LISN, (9) 150 kHz – 30 MHz, 50 µH || 50 Ohm, 1 x 800 A continuously (1000 A short time), wing terminals, low voltage drop, High power resistors, cooling fans. Max. Voltage: 1000 V DC or 650 V AC 50/60 Hz.
|
|
|
Single path LISN (Automotive) CISPR 25 / ISO 7637
|
NNBM 8124
|
Automotive LISN according CISPR 25 and ISO 7637-2 and for BCI Testing. Impedance (5µH + 1 Ohm) || 50 Ohm. Max. 70 (100) A. With switchable 50 Ohm load and switchable 1 microfarad capacitor at mains side, single path, BNC female connector.
|
Opt. N
|
Option for NNBM 8124: N-female connector instead of BNC.
|
NNBM 8124-200
|
Automotive LISN according CISPR 25 and ISO 7637-2 and for BCI Testing. Impedance (5µH + 1 Ohm) || 50 Ohm. Max.200 A. With switchable 50 Ohm load and switchable 1 mikrofarad capacitor at mains side, single path, BNC female connector.
|
Opt. N
|
Option for NNBM 8124-200: N-female connector instead of BNC.
|
NNBM 8124-400
|
Automotive LISN according CISPR 25 and ISO 7637-2 and for BCI Testing. Impedance (5µH + 1 Ohm) || 50 Ohm. Max. 400 A. With switchable 50 Ohm load and switchable 1 mikrofarad capacitor at mains side, single path, BNC female connector.
|
Opt. N
|
Option for NNBM 8124-400: N-female connector instead of BNC.
|
NNBM 8126 A 890
|
LISN 5 µH || 50 Ohm, 70 (100) single path. Similar to NNBM 8126 A but suitable for 600V DC and 270 V AC 890 Hz. Calibrated up to 400 MHz according to DO-160.
|
|
|
Two path LISN (Automotive) CISPR 25 / ISO 7637
|
NNBM 8126 G
|
LISN 5 µH || 50 Ohm, 70 (100) A, two paths, two BNC connectors, including 1 each 50 Ohm dummy load.
|
|
|
HV-LISN according to CISPR 25 Ed. 4 or BMW GS 95025-1
|
NNHV 8123
|
High Voltage LISN according to CISPR 25 Ed. 4 or BMW GS 95025-1 to measure the conducted disturbance voltage on shielded lines for (hybrid) electric vehicles (HEV, EV), can be used for BCI with an external dummy load, impedance (5µH) || 50 Ohm. 70 (100) A, 1000 V DC. Backside with built in 0.1 microfarad capacitor to ground, N-jack. Normally used in pairs inside the enclosure HVSE 8600!
|
NNHV 8123-200
|
High Voltage LISN according to CISPR 25 Ed. 4 or BMW GS 95025-1 to measure the conducted disturbance voltage on shielded lines for (hybrid) electric vehicles (HEV, EV), can be used for BCI with an external dummy load, impedance (5µH) || 50 Ohm. 200 A, 1000 V DC. Backside with built in 0.1 microfarad capacitor to ground, N-jack. Normally used in pairs inside the enclosure HVSE 8600!
|
NNHV 8123-400
|
High Voltage LISN according to CISPR 25 Ed. 4 or BMW GS 95025-1 to measure the conducted disturbance voltage on shielded lines for (hybrid) electric vehicles (HEV, EV), can be used for BCI with an external dummy load, impedance (5µH) || 50 Ohm. 400 A, 1000 V DC. Backside with built in 0.1 microfarad capacitor to ground, N-jack. Normally used in pairs inside the enclosure HVSE 8600!
|
HVSE 8600
|
Shielded housing for 2 HV-LISN, 2 paths with cable feed through for HV+ and HV-, shield can be connected to the housing, 2 measurement ports N, 1 monitor port N, with connecting cables between inside measurement ports and outside N- connectors. All models of the NNHV- and NNBM-series can be inserted. For full CISPR 25 Ed. 4 compliance a modification of the back side circuitry of the NNBM series is required!
|
Opt. 8600-100
|
1 pair of flange panels for HVSE 8600 with cable feed through for shielded cables up to ca. 100 A.
|
Opt. 8600-200
|
1 pair of flange panels for HVSE 8600 with cable feed through for shielded cables suitable for max. currents in a range of ca. 100 A to 200 A.
|
Opt. 8600-400
|
1 pair of flange panels for HVSE 8600 with cable feed through for shielded cables suitable for a range of ca. 200 A to 400 A.
|
|
|
BAN Broadband Artificial Networks according ISO 11452-7 or DC-10614
|
BAN 8508
|
BAN broadband artificial network 2 A – 8 A according ISO 11452-7 or DC-10614
|
BAN 8530
|
BAN broadband artificial network 8 A – 30 A according ISO 11452-7 or DC-10614
|
DC-Block 500
|
DC-blocking capacitor BNC for direct injection with BAN
|
|
|
LISN according to MIL 461 MIL 462
|
NNBL 8225
|
V-LISN (9) 150 kHz – 100 MHz, 50 µH + 5 Ohm || 50 Ohm, 20 A, 50 Hz AC 250V, single path, Mil. Std. 461/462.
|
NNBL 8226
|
V-LISN (9) 150 kHz – 100 MHz, 50 µH + 5 Ohm || 50 Ohm, 70 (100) A, 50 Hz AC 250 V, single path, Mil. Std. 461/462.
|
NNBL 8226- HV
|
V-LISN (9) 150 kHz – 100 MHz, 50 µH + 5 Ohm || 50 Ohm, 70 (100) A, 50 Hz AC 800 V, single path, Mil. Std. 461/462.
|
NNBL 8226-2
|
V-LISN (9) 150 kHz – 100 MHz, 50 µH + 5 Ohm || 50 Ohm, 70 (100) A, 50 Hz AC 250 V, two path, Mil. Std. 461/462.
|
NNBL 8230
|
V-LISN (9) 150 kHz – 100 MHz, 50 µH + 5 Ohm || 50 Ohm, 300 A, 50 Hz AC 250 V, single path, Mil. Std. 461/462.
|
|
|
Special LISN and accessories
|
NDTV 8160
|
Universal Delta-, T-, V-LISN
|
PVDC 8300
|
PV LISN, 1500 V, 50 A, common mode impedance 150 Ohm, Z differential mode = 100 Ohm, air coils 280 microhenry.
|
PVDC 8300 Opt. Fans
|
Option for PVDC 8300: Fans for a maximum continuous current of 100 A.
|
PVDC 8301
|
PV-LISN for the DC side of grid connected power converters GCPC, 1500 V, 200 A, common mode impedance = 150 Ohm, differential mode impedance = 100 Ohm, air coils 280 microhenry.
|
TEMP 8400
|
Tempest LISN 9 kHz to 1 GHz, 2 path model 10 A, N-connectors for DuT power supply and N-connectors for the 2 measurement ports. The unit allows to listen to even the smallest signals on power lines.
|
TEMP 8401
|
Adapter N-male to wing terminals for TEMP 8400
|
NPLC 8500
|
LISN according to recommendation ITU-T G.9901: 250 Volt 16 A, 1 path, wing terminals, measuring output BNC, to measure the power spectral density of PRIME transceivers for power line communication.
|
CMDM 8700
|
Common mode differential mode noise separator for V-LISN, 2 BNC inputs, 1 BNC output. 9 kHz-30 MHz.
|
|
|
ISN / T-Networks
|
NTFM 8131
|
T-ISN 150 Ohm asymmetric 50 Ohm unsymmetrical, 2-wire, 400 V AC, 9 kHz – 30 MHz, CISPR 22 D1/EN55015-2002
|
NTFM 8158
|
ISN T8 CAT6 (LCL = 75 dB) according CISPR 22 edition 5.2, figure D.3. for up to 4 pairs UTP.
|
CAT5 8158
|
ISN T8 CAT5 (LCL = 65 dB) according CISPR 22 edition 5.2, figure D.3. for up to 4 pairs UTP.
|
CAT3 8158
|
ISN T8 CAT3 (LCL = 55 dB) according CISPR 22 edition 5.2, figure D.3. for up to 4 pairs UTP.
|
ISN S8
|
ISN for screened RJ45 or RJ11 connections, 2, 4 or 8 wire, according D.11 CISPR 22 Ed.5.2.
|
ISN S1
|
ISN according CISPR 22 Ed.5.5:2006, Annex D, D9 for coaxial lines
|
|
|
Voltage Probes
|
TK 9417
|
HF-Probe, 2.5 kOhm
|
TK 9420
|
High-Voltage-Probe, 1.5 kOhm, 4 pF, 9 kHz – 30 MHz, RF < 30 V
|
VT 9420
|
Plug-In divider 1.5 kOhm for TK 9420 probe for determination of disturbance source impedance
|
TK 9421
|
High Power Voltage Probe, 1.5 kOhm, 4 pF, 150 kHz – 30 MHz RF < 100 V
|
TK 9422
|
High Power Voltage Probe, 5 kOhm, 4 pF, (9) 150 kHz – 30 MHz RF < 100 V
|
|
|
EMI Receivers
|
FCKL 1528
|
EMI Receiver according CISPR 16-1, 9 kHz – 30 MHz, 5 Detectors: Quasipeak, Peak, Average, CAV, CRMS. Attenuator with 1 dB steps, Protected Input, Automatic Calibration w. built-in Pulse Generator, GPIB-Interface.
|
Opt. XY-Rec.
|
Option: 25-pin connector on the back side with analogous voltages for frequency and Interference voltage to connect an XY-recorder.
|
Opt. TG
|
Option: Built-In Tracking Generator, Output Level 120 dBµV.
|
Opt. Softw.
|
Option: Schwarzbeck-Software FCKL for EMI-Measurement
|
FCVU 1534
|
EMI Receiver according CISPR 16-1, 20 – 1050 MHz, 5 Detectors: Quasipeak, Peak, Average, CAV and CRMS, Attenuator with 1 dB steps, Protected Input, Automatic Calibration w. built-in Pulse Generator, GPIB-Interface.
|
Opt. XY-Rec.
|
Option: 25-pin connector on the back side with analogous voltages for frequency and Interference voltage to connect an XY-recorder.
|
Opt. TG
|
Option: Built-In Tracking Generator, Output Level 120 dBµV P.D.
|
Opt. Softw.
|
Option: Schwarzbeck-Software FCVU for EMI-Measurement
|
FCLE 1535
|
EMI Receiver according CISPR 16-1, 9 kHz – 3.25 GHz, 5 Detectors: Quasipeak, Peak, Average, CAV and CRMS. Protected Input, Automatic Calibration w. built- in Pulse Generator, GPIB-Interface.
|
Opt. Softw.
|
Option: Schwarzbeck-Software for FCLE for EMI-Measurement
|
INES PCI 488
|
IEEE 488 32-bit PCI-Slot PC Plug-In Card (BKAB 488 necessary)
|
INES PCMCIA 488
|
IEEE 488 32-bit PCMCIA (Type II) Plug-In Card for portable Computers (Notebook) including 2 m cable
|
BKAB 488
|
IEEE 488 cable, 2 m, necessary for PCI card, not necessary for PCMCIA card
|
|
|
Pulse Generators
|
IGUU 2916
|
Universal Calibration Pulse Generator according CISPR 16 for Bands A, B, C, D (9 kHz – 1000 MHz), especially for EMI Receiver Tests (Pulse weighting, Overload), Signal generator 100 kHz, 1 MHz, 10 MHz, 100 MHz (60 dBµV). Pulse Repetition Frequency 0.1 Hz – 200 Hz (20 kHz), Output Level adjustable in 1 dB steps, GPIB-Interface.
|
Opt. RecTest Softw.
|
Option: Receiver Test Software for IGUU 2916 or 2918 signal generator and EMI- receiver to perform an automatic calibration of an EMI receiver according to CISPR 16-1-1.
|
Opt. KU 9616
|
Option: Coaxial Switching Unit for automatic performance tests with IGUU 2916, N-Connectors female.
|
IGUU 2918
|
Calibration-Pulse Generator according CISPR 16 for Band A, B, C, D (9 kHz-1000 Hz) To calibrate the pulse response of EMI receivers. Pulse repetition frequency main generator 0.1 – 200 Hz (aux. generator up to 1 MHz) with IEEE-488 Interface.
|
Opt. RecTest Softw.
|
Option: Receiver Test Software for IGUU 2916 or 2918 signal generator and EMI- receiver to perform an automatic calibration of an EMI receiver according to CISPR 16-1-1.
|
Opt. KU 9618
|
Option: KU 9618 Coaxial Switching Unit for automatic performance tests with IGUU 2918, N-Connectors female
|
IGUF 2910
|
Battery driven High Power Pulse Generator, Pulse Repetition Frequency 300 Hz, weighted CISPR Level 80 dbµV (Quasipeak, 120 kHz IF-BW). Broad band signal source up to 300 (1000) MHz w. 0.5 ns Pulses of 300 V at 50 Ohm
|
LGA 9802
|
Automatic Charging Unit 230 V for IGUF 2910
|
|
|
Accessories
|
|
|
Coaxial Cables
|
AK 9513
|
50 Ohm Coax. Cable with N plugs, individual length, usable up to 3 (5) GHz, Basic price Euro 80,00 + price / m Euro 5,00 + price for individual calibration Euro 80,00. Indiv. Cal. possible if cable longer than 3 m. Standard lengths: 3 m, 5 m, 10 m.
|
AK 9515 D
|
50 Ohm Coaxial Cable with N plugs, low loss, limited flexibility, usable up to 10 (18) GHz, 10.5 mm diam.
|
AK 9515 E
|
50 Ohm Coaxial Cable with N plugs, low loss, good flexibility, usable up to 10 (18) GHz, 10.8 mm diam.
|
AK 9515 G
|
50 Ohm Coaxial Cable available with N- or 7/16-plugs,very low loss, high power, good flexibility, usable up to 6 GHz, 14.6 mm diam.
|
AK 9515 H
|
50 Ohm Microwave Coaxial Cable with N- or SMA-connectors, low loss, flexible, usable up to 18 GHz.
|
MSS 9630
|
Sheath current blocking cable to avoid coupling effects caused by braid currents. Standard configuration: N-male, N-female, length ca. 0.3 m
|
|
|
Fixed Attenuators
|
DGA 9552 N
|
Bidirectional Attenuator N-female N-male to 18 GHz, 50 Ohm 5 Watt. Available values: 3 dB, 6 dB, 10 dB, 20, 30, 40 dB.
|
VTSD 9561 F
|
Diode Pulse Limiter + 10 dB Attenuation, fuse lamp, N or BNC, please select!
|
VTSD 9561 D
|
Diode Pulse Limiter + 20 dB Attenuation, fuse lamp, BNC
|
VTSD 9562
|
Bandpass and Limiter for Partial Discharge Measurements BNC
|
|
|
Current Clamps and calibration adapters
|
SW 9602
|
Current Transformer, shielded, 0.01 – 200 MHz, Transfer Impedance: 1 Ohm for wires up to 6.5 mm.
|
SW 9603
|
Current Transformer, shielded, 9 kHz – 150 MHz, Transfer Impedance: 1 Ohm for wires up to 14 mm.
|
SW 9605
|
Current Transformer Clamp CISPR 22, 9 kHz – 80 MHz, Transfer Impedance: 1
Ohm for wires up to 23 mm.
|
SW 9606
|
Current injection clamp for RF current injection into harnesses up to 23 mm diamter, transducer 18 dB.
|
CA 9607
|
Universal calibration adapter for current clamps, test jig for ferrites, length adjustable.
|
CA 9608
|
Universal calibration adapter for e.g. the following current clamps: R&S ESV-Z1, Prodyn, IT-050-1, length and height settable.
|
|
|
Baluns
|
SY 9223-120
|
Balun for transmission measurements according to IEC61643-21. 50 Ohm N to 120 Ohm screw terminals.
|
SY 9223- CISPR 13
|
Broad band isolation transformer according CISPR 13 fig. A.2, 50 Ohm 75 Ohm.
|
SY 9223-PLC
|
1:1 PLC balun according to EN 50065-2-1 2003 + A1:2005 für Immunity against small band disturbance voltage. 3 kHz – 30 MHz, BNC and banana jacks.
|
Opt. 2 µF + 50 Ohm
|
Opt. for SY 9223-PLC: 2 µF + 50 Ohm, in isolated housing, banana jacks.
|
SY 9501
|
Balun unsymm. 50 Ohm to symm. 150 Ohm EN 55015, CISPR 15
|
SY 9223-17-100
|
Broadband transformer 1:1,4 or 50 Ohm : 100 Ohm respectively according to CISPR 17 for filter measurements. 100 Ohm-side with banana jacks. 50 Ohm-side with BNC-jacks.
|
SY 9223-17-0.1
|
Broadband transformer 22:1 or 50 Ohm : 0.1 Ohm respectively according to CISPR 17 for filter measurements. 50 Ohm-side with BNC-jacks, 0.1 Ohm-side with banana jacks.
|
|
|
Other passive devices
|
BD 9501
|
IEEE-488 Bus-Feed through for flange mounting (shielded rooms) (other feed throughs on request)
|
HPF
|
High Pass Filter 35 – 1000 MHz, Insertion loss at 27.12 MHz typ. 100 dB
|
TF 130-150
|
Test Fixture for Ford RI 130/ 150 Per EMC-CS-2009
|
VDHH 9502
|
Van der Hoofden test head with protection network and individual calibration of the network according IEC62493 or VDE 0848-493.
|
CISPR 17 Equipment
|
Transformers, fixtures and adapters to measure filters, ferrites and other passive components. Detailed product list and data sheets on request.
|
BN 1701
|
Buffer network (set of 2 pieces) according CISPR 17 Annex D2, D3, max. current: 32A, connectors: wing terminals, BNC female.
|
CCC 9224
|
Capacitive coupling clamp for transients according to ISO 7637-3 or DC-10614 B.5.
|
CCP 9225
|
Capacitive coupling plate similar to ISO 7637-3 according to MBN 10284-2, 2011-04 or MBN 10284-4, 2011-04 for CV tests.
|
|
|
Preamplifiers
|
BBV 9743
|
Broadband Coaxial Preamplifier gain max. 30 dB, 10 MHz – 6 GHz, low noise floor, N-jack N-plug, including power supply.
|
BBV 9744
|
Broadband Coaxial Preamplifier gain max. 30 dB, 9 kHz – 6 GHz, low noise floor, N-jack N-plug, including power supply.
|
BBV 9745
|
Broadband Coaxial Preamplifier gain max. 30 dB, 9 kHz –2 GHz, low noise floor, N-jack N-plug, improved ESD protection, including power supply.
|
BBV 9718
|
Broadband Coaxial Preamplifier typ. 33 dB, 1 – 18 GHz with fixture for 22 mm antenna tube, and N to SMA cable, power supply 12 V 250 mA necessary.
|
Opt. PS
|
Option Power supply for BBV 9718 or 9719.
|
Opt. Battery
|
Option Rechargeable battery pack for BBV 9718 or 9719.
|
Opt. ALCS 2-24A
|
Battery charger ALCS 2-24A for rechargeable battery pack
|
BBV 9719
|
Broadband Coaxial Preamplifier typ. 33 dB, 18-26.5 GHz, power supply 12 V 300 mA necessary. Including short cable with SMA plugs to connect the BBV 9719 with the antenna (for example BBHA 9170).
|
Opt. PS
|
Option Power supply for BBV 9718 or 9719.
|
Opt. Battery
|
Option Rechargeable battery pack for BBV 9718 or 9719.
|
Opt. ALCS 2-24A
|
Battery charger ALCS 2-24A for rechargeable battery pack.
|
BBV 9721
|
Broadband Coaxial Preamplifier typ. 30 dB, 18-40 GHz. Including short cable with 2.92 plugs to connect the BBV 9721 with the antenna (for example BBHA 9170). Noise figure 5.5 dB, P1dBmin=15 dBm, VSWR max in/out = 2,6.
|
Opt. PS 9721
|
Power supply unit for BBV 9721 including cables with secuity plugs, can be used for 110 and 230 V.
|
Opt. PS 9721 Battery
|
Power supply unit for BBV 9721 including cables with security plugs, can be used for 110 V and 230 V. Built in rechargeable battery. This unit can supply power to the BBV 9721 without connection to mains. Charging electronics also included.
|
|
|
Reference radiators, comb generators
|
SG 9301
|
Spectrum Generator 30-1000 MHz, spectrum lines switchable 100 Hz – 1 MHz, N-female connector, charger ACS 110 required, main application: reference radiator (antenna required e.g. UBAA 9114 with BBVU 9135)
|
Opt. ACS 110
|
Option: Charger ACS 110 for SG 9301.
|
SG 9302
|
Comb generator 0.1 – 18 GHz, spectrum lines every 100 MHz, battery driven, including charger for 230 V.
|
|
|
Field probes
|
VUFM 1670
|
E-Field Meter 70 kHz-3 GHz, 1V/m-300V/m, linear polarized, charger ACS 110 required.
|
VUFM 1671
|
LCD-Display Unit for VUFM 1670 with 5 m fibre optical link, Additional cost for longer fibre: Euro 5,00/m, charger ACS 110 required.
|
VUFM 1672
|
LCD–Display Unit VUFM 1672 for E – Field-Meter VUFM 1670 with optical link and IEEE 488 / GPIB – Interface.
|
|
|
Other active devices
|
VHIC 9260
|
Impedance converter according CISPR 25 9 kHz – 30 (120) MHz.
|
Opt. ACS 110
|
Option: Charger ACS 110 for VHIC 9260.
|
CVP 9222
|
High Impedance Capacitive Voltage Probe according to CISPR 22, EN 55022 C 1.3. Frequency range: 9 kHz – 100 MHz.
|
Opt. ACS 110
|
Option: Charger ACS 110 for CVP 9222.
|
Opt. CAL 9222
|
Option: Calibration Adapter for CVP 9222.
|
|
|
Near Field Probes
|
FS-SET 7100
|
Nearfield Probe Set including HFSL, HFSH, EFS and Separator EW and AC/DC Adaptor in storing case.
|
HFSL 7101
|
Active Near Field Probe (magnetic) 9 kHz – 30 MHz (EW 7110 required)
|
HFSH 7102
|
Active Near Field Probe (magnetic) 4 MHz – 1000 MHz (EW 7110 required)
|
EFS 7103
|
Active Near Field Probe (electric) 9 kHz – 1000 MHz (EW 7110 required)
|
EW 7110
|
Coaxial DC-Separator for Near Field Probes HFSL, HFSH, EFS
|
ACDC 7110
|
AC/DC Adapter for DC-Separator EW 7110
|
|
|
Strip lines
|
TEMZ 5231
|
50 Ohm Strip line according to ISO 11452-5 for automotive testing, 4.3 x 1.5 x 0.15 m, septum with cylindrical rods, N-connectors, wooden base construction and termination required.
|
Opt. Termination 150 W
|
Option: 50 Ohm termination, N-jack,150 Watt, connecting cable for TEMZ 5231
|
Opt. Termination 500 W
|
Option: 50 Ohm termination, N-jack, 500 Watt, connecting cable, for TEMZ 5231
|
Opt. Foldaway
|
Instead of cylindrical rods to hold the septum there will be side arms. The cell can be folded away vertically. A stainless steel construction with caster wheels supports the cell. Must be ordered together with TEMZ 5231, cannot be refitted.
|
TEMZ 5232
|
90 Ohm Strip line according to ISO 11452-5 for automotive testing, 3.5 x 0.9 x 0.15 m, N-connector, built-in termination 90 Ohm, 50 W, wooden base construction required
|
TEMZ 5233
|
Closed, unsymmetrical 50 Ohm strip line DC – 420 (600) MHz, Crawford TEM Cell, for E- field probe and H-field probe calibration and for immunity testing. ISO 11452-3, IEEE 1309 under EN 61000-4-20.
|
TEMZ 5236
|
Symmetrical Strip line 0.96 x 0.6 x 0.6 m, BNC-connectors, including 4:1 transformer and 50 W dummy load.
|
TEMZ 5238
|
Symmetrical strip line according to CISPR 20 up to 120 MHz.
|
|
|
Calibration adapters for V-LISN (V-AMN)
|
KA 8127
|
BNC female to Schuko male. Fits for all LISN types with Schuko socket e.g. NSLK 8127, NSLK 8126, NSLK 8128
|
KA 8126
|
BNC female to CEE / CEKON 16 A male. Fits for all LISN with 16 A three-phase connector e.g. NSLK 8126. Diameter of Phase rods: 5 mm. Diameter of Neutral rod: 6,9 mm.
|
KA 8128
|
BNC female to CEE / CEKON 32 A male. Fits for all LISN with 32 A three-phase connector e.g. NSLK 8128. Diameter of Phase rods: 5,9 mm. Diameter of Neutral rod: 8 mm.
|
KA 8121
|
BNC female to 4 mm banana plug. Fits for NNLK 8121 and NDTV 8160.
|
KA 8129
|
BNC female to 4 mm banana plug. Fits for NNLK 8129.
|
KA 8130
|
BNC female to 4 mm banana plug. Fits for NNLK 8130 and NNLK 8140.
|
KA 8125
|
BNC female to terminal wings. Fits for NNBM 8124, NNBM 8125, NNBM 8126 A, NNBM 8125 BCI and NNBL 8225. Diameter of terminals: 8,5 mm, distance of terminals: 60 mm
|
KA 8126 D
|
BNC female to terminal wings. Fits for NNBM 8126 D, NNBL 8226-HV, NNBL 8226, NNBL 8226-2, NNBM 8125 BCI with Option 200 A, NNBM 8124-200, NNBM 8126 G. Diameter of
terminals: 8,5 mm, distance of terminals: 90 mm
|
KA 8126 F
|
BNC female to terminal wings. Fits for NNBM 8126 E, NNBM 8126 F, NNBM 8126 F HYB up to S/N 148. Diameter of terminals: 12,4 mm, distance of terminals: 90 mm
|
KA 8126 F HYB
|
BNC female to terminal wings. Fits for NNBM 8124-400, NNBM 8126 F HYB starting from S/N 149. Diameter of terminals: 16,4 mm, distance of terminals: 110 mm
|
MSS 9630
|
Sheath current blocking cable to avoid coupling effects caused by braid currents. Standard configuration: N-male, N-female, length ca. 0.2-0,3 m
|
|
|
CDN according EN 61000-4-6, CDNE according CISPR 16-1-2 CISPR 15, ferrite clamps, absorbing clamps
|
|
|
M-Type CDN for mains lines
|
CDN M1
|
CDN for Earth conductor 250V AC / 1,000V DC, 16A, 150kHz – 230MHz
|
CDN M1-32A
|
CDN for Earth conductor 250V AC / 1,000V DC, 32A, 150kHz – 230MHz
|
CDN M1- 32A/1000V
|
CDN for Earth conductor 1,000V AC / 1,000V DC, 32A, 150kHz – 80MHz
|
CDN M1-50A
|
CDN for Earth conductor 250V AC / 750V DC, 50A, 150kHz – 80MHz, incl. high- current MC connectors for AE and DUT port
|
CDN M1-75A
|
CDN for Earth conductor 250V AC / 750V DC, 75A, 150kHz – 80MHz, incl. high- current MC connectors for AE and DUT port
|
CDN M1-100A
|
CDN for Earth conductor 250V AC / 750V DC, 100A, 150kHz – 80MHz, incl. high- current MC connectors for AE and DUT port
|
CDN M2
|
CDN for two mains supply lines 250V AC / 250V DC, 16A, 150kHz – 300MHz, AE port with IEC 320 connector
|
CDN M2 Banana
|
CDN for two mains supply lines 250V AC / 1,000V DC, 16A, 150kHz – 230MHz, AE port with banana connectors
|
CDN M2-500V
|
CDN for two mains supply lines 500V AC / 1,000V DC, 16A, 150kHz – 80MHz
|
CDN M2-750V
|
CDN for two mains supply lines 750V AC / 1,000V DC, 16A, 150kHz – 80MHz
|
CDN M2-1000V
|
CDN for two mains supply lines 1,000V AC / 1,000V DC, 16A, 150kHz – 80MHz
|
CDN M2-32A
|
CDN for two mains supply lines 250V AC / 1,000V DC, 32A, 150kHz – 230MHz
|
CDN M2-32A/750V
|
CDN for two mains supply lines 750V AC / 1,000V DC, 32A, 150kHz – 80MHz
|
CDN M2-32A/1000V
|
CDN for two mains supply lines 1,000V AC / 1,000V DC, 32A, 150kHz – 80MHz
|
CDN M2-50A
|
CDN for two mains supply lines 250V AC / 750V DC, 50A, 150kHz – 80MHz, incl. high-current MC connectors for AE and DUT port
|
CDN M2-50A/750V
|
CDN for two mains supply lines 750V AC / 750V DC, 50A, 150kHz – 80MHz, incl. high-current MC connectors for AE and DUT port
|
CDN M2-75A
|
CDN for two mains supply lines 250V AC / 750V DC, 75A, 150kHz – 80MHz, incl. high-current MC connectors for AE and DUT port
|
CDN M2-100A
|
CDN for two mains supply lines 250V AC / 750V DC, 100A, 150kHz – 80MHz, incl. high-current MC connectors for AE and DUT port
|
CDN M2/M3
|
CDN for two or three supply lines, switchable, 250V AC / 250V DC, 16A, 150kHz – 300MHz, AE port with IEC 320 connector, CDNE M2 or CDNE M3 for CISPR 15 also available!
|
CDN M3
|
CDN for three mains supply lines 250V AC / 250V DC, 16A, 150kHz – 300MHz, AE port with IEC 320 connector
|
CDN M3 Banana
|
CDN for three mains supply lines 250V AC / 1,000V DC, 16A, 150kHz – 230MHz, AE port with banana connectors
|
CDN M3-500V
|
CDN for three mains supply lines 500V AC (L+N+PE) / 1,000V DC, 16A, 150kHz – 80MHz
|
CDN M3-400V Delta
|
CDN for three mains supply lines 3x400V AC (L1+L2+L3) / 1,000V DC, 16A, 150kHz – 230MHz
|
CDN M3-32A
|
CDN for three mains supply lines 250V AC / 1,000V DC, 32A, 150kHz – 230MHz
|
CDN M3-32A/400V Delta
|
CDN for three mains supply lines 3x400V AC (L1+L2+L3), 32A, 150kHz – 230MHz
|
CDN M3-32A/750V
|
CDN for three mains supply lines 750V AC (L+N+PE) / 1,000V DC, 32A, 150kHz – 80MHz
|
CDN M3-32A/750V Delta
|
CDN for three mains supply lines 3x750V AC (L1+L2+L3) / 1,000V DC, 32A, 150kHz – 80MHz
|
CDN M3-50A
|
CDN for three mains supply lines 250V AC / 750V DC, 50A, 150kHz – 80MHz, incl. high-current MC connectors for AE and DUT port
|
CDN M3-75A
|
CDN for three mains supply lines 250V AC / 750V DC, 75A, 150kHz – 80MHz, incl. high-current MC connectors for AE and DUT port
|
CDN M3-100A
|
CDN for three mains supply lines 250V AC / 750V DC, 100A, 150kHz – 80MHz, incl. high-current MC connectors for AE and DUT port
|
CDN M4 PE
|
CDN for four mains supply lines (L1+L2+L3+PE) 3x400V AC, 16A, 150kHz – 230MHz
|
CDN M4 N
|
CDN for four mains supply lines (L1+L2+L3+N) 3x400V AC, 16A, 150kHz – 230MHz
|
|
|
S-Type CDN for shielded lines and coaxial cables
|
CDN S1-50 BNC
|
CDN for screened coaxial cable, single line, 50ohm BNC, 100V AC / 100V DC, 0.25A, 150kHz – 230MHz
|
CDN S1-50 N
|
CDN for screened coaxial cable, single line, 50ohm N, 100V AC / 100V DC, 0.25A, 150kHz – 230MHz
|
CDN S1-50 SMA
|
CDN for screened coaxial cable, single line, 50ohm SMA, 100V AC / 100V DC, 0.25A, 150kHz – 230MHz
|
CDN S1-75 BNC
|
CDN for screened coaxial cable, single line, 75ohm BNC, 100V AC / 100V DC, 0.25A, 150kHz – 230MHz
|
CDN S1-75 N
|
CDN for screened coaxial cable, single line, 75ohm N, 100V AC / 100V DC, 0.25A, 150kHz – 230MHz
|
CDN S2 BNC
|
CDN for two screened cables, BNC conn., 100V AC / 100V DC, 1.5A, 150kHz – 80MHz
|
CDN S4 BNC
|
CDN for four screened cables, BNC conn., 100V AC / 100V DC, 1.5A, 150kHz – 80MHz
|
CDN S4 USB
|
CDN for screened cable, four lines, USB A conn., 100V AC / 100V DC, 1A, 150kHz – 230MHz
|
CDN S4-3A BNC
|
CDN for screened cable, four lines, BNC conn., 100V AC / 100V DC, 3A, 150kHz – 80MHz
|
CDN S8 RJ45
|
CDN for screened cable, eight lines, RJ45 conn., 100V AC / 100V DC, 1.5A, 150kHz – 230MHz
|
CDN S9
|
CDN for screened cable, nine lines, Sub-D9, 125V AC / 125V DC, 1.5A, 150kHz – 230MHz
|
CDN S15
|
CDN for screened cable, 15 lines, Sub-D15, 125V AC / 125V DC, 1.5A, 150kHz – 230MHz
|
CDN S15 VGA
|
CDN for screened cable, 15 lines, VGA conn., 125V AC / 125V DC, 1.5A, 150kHz – 230MHz
|
CDN S25
|
CDN for screened cable, 25 lines, Sub-D25, 125V AC / 125V DC, 1.5A, 150kHz – 230MHz
|
CDN S37
|
CDN for screened cable, 37 lines, Sub-D37, 125V AC / 125V DC, 0.25A, 150kHz – 80MHz
|
CDN S50
|
CDN for screened cable, 50 lines, Sub-D50, 125V AC / 125V DC, 0.25A, 150kHz – 80MHz
|
|
|
T-Type CDN for balanced unscreened communication lines
|
CDN T2
|
CDN for unscreened balanced pair, RJ11/banana conn, 63V AC / 100V DC, 1.5A, 150kHz – 230MHz
|
CDN T2-3A
|
CDN for unscreened balanced pair, banana conn, 63V AC / 100V DC, 3A, 150kHz – 80MHz
|
CDN T2-5A
|
CDN for unscreened balanced pair, banana conn, 63V AC / 100V DC, 5A, 150kHz – 80MHz
|
CDN T4
|
CDN for two unscreened balanced pairs, banana conn, 63V AC / 100V DC, 1.5A, 150kHz – 230MHz
|
CDN T4 XLR
|
CDN for two unscreened balanced pairs, XLR conn, 50V AC / 50V DC, 1.5A, 150kHz – 230MHz
|
CDN T4 RJ45
|
CDN for two unscreened balanced pairs, RJ45 conn, 63V AC / 100V DC,1.5A, 150kHz – 230MHz
|
CDN T4-3A
|
CDN for two unscreened balanced pairs, banana conn, 63V AC / 100V DC, 3A, 150kHz – 80MHz
|
CDN T8 RJ45
|
CDN for 4 unscreened balanced pairs, RJ45 conn, 63V AC / 100V DC, 1.5A, 150kHz – 230MHz
|
CDN T8-3A
|
CDN for 4 unscreened balanced pairs, banana conn, 63V AC / 100V DC, 3A,
150kHz – 80MHz
|
|
|
AF-Type CDN for non balanced data lines
|
CDN AF2
|
CDN for 2 unscreened unbalanced lines, banana conn, 63V AC /100V DC, 1.5A, 150kHz – 300MHz, incl. VDF data for CISPR 15
|
CDN AF2-250V
|
CDN for 2 unscreened unbalanced lines, banana conn, 250V AC / 250V DC, 1.5A, 150kHz – 80MHz
|
CDN AF3
|
CDN for 3 unscreened unbalanced lines, banana conn, 63V AC / 100V DC, 1.5A, 150kHz – 300MHz, incl. VDF data for CISPR 15
|
CDN AF3-3A
|
CDN for 3 unscreened unbalanced lines, banana conn, 63V AC / 100V DC, 3A, 150kHz – 80MHz
|
CDN AF3-250V
|
CDN for 3 unscreened unbalanced lines, banana conn, 250V AC / 250V DC, 1.5A, 150kHz – 80MHz
|
CDN AF4
|
CDN for 4 unscreened unbalanced lines, banana conn, 63VAC / 100V DC, 1.5A, 150kHz – 230MHz
|
CDN AF5
|
CDN for 5 unscreened unbalanced lines, banana conn, 63V AC / 100V DC, 1.5A, 150kHz – 80MHz
|
CDN AF6
|
CDN for 6 unscreened unbalanced lines, banana conn, 63V AC / 100V DC, 1.5A, 150kHz – 80MHz
|
CDN AF6-250V
|
CDN for 6 unscreened unbalanced lines, banana conn, 250V AC / 250V DC, 1.5A, 150kHz – 80MHz
|
CDN AF8
|
CDN for 8 unscreened unbalanced lines, banana conn, 63V AC / 100V DC, 1.5A, 150kHz – 80MHz
|
CDN AF10
|
CDN for 10 unscreened unbalanced lines, D-Sub15 conn, 63V AC / 100V DC, 1.5A, 150kHz – 80MHz
|
CDN AF15
|
CDN for 15 unscreened unbalanced lines, D-Sub15 conn, 63V AC / 100V DC, 1.5A, 150kHz – 80MHz
|
CDN AF25
|
CDN for 25 unscreened unbalanced lines, D-Sub25 conn, 63V AC / 100V DC, 1.5A, 150kHz – 80MHz
|
|
|
Special CDN
|
CDN CAN-4
|
CDN 4 CAN-Bus, 4-wire, unscreened, 48V, 2A (supply lines, pins 3 (GND) and 9(V+)) and 48V, 2A (CAN-BUS lines, pins 2 CAN-L and 7 CAN-H), 150kHz – 230MHz, Sub-D9 connector
|
|
|
CDNE for emission measurement on luminaries according EN 55015
|
CDNE M2
|
CDNE with tight tolerances for CISPR 15 emission measurements with 2 mains conductors can also be used as CDNE AF2.
|
CA CDNE M2 Part A
|
Part A of the calibration or short adapter for CDNE M2
|
CA CDNE Part B
|
Part B of the calibration or short adapter for CDNE M2 or M3
|
SR100-6W
|
Adapter 150 to 50 Ohm for CDNE or ISN e.g. ISN S8 or CDNE M2, 0-500 MHz, 6W, connectors: BNC female, 4 mm security banana jack.
|
CDNE M3
|
CDNE with tight tolerances for CISPR 15 emission measurements with 3 mains conductors.
|
CA CDNE M3 Part A
|
Calibration or short adapter for CDNE M3 part A.
|
|
|
CDN for IEC 60945 or EN 61326-3-2 10kHz – 80MHz
|
CDN M1-10kHz
|
CDN for Earth conductor 250V AC / 1,000V DC, 16A, 10kHz – 80MHz
|
CDN M2-10kHz
|
CDN for two mains supply lines 250V AC / 1,000V DC, 16A, 10kHz – 80MHz
|
CDN M2-10kHz/500V
|
CDN for two mains supply lines 500V AC / 1,000V DC, 16A, 10kHz – 80MHz
|
CDN M3-10kHz
|
CDN for three mains supply lines 250V AC / 1,000V DC, 16A, 10kHz – 80MHz
|
CDN T2-10kHz
|
CDN for unscreened balanced pair, RJ11/banana conn, 63V AC / 100V DC, 1.5A, 10kHz – 80MHz
|
CDN T8-10kHz
|
CDN for 4 unscreened balanced pairs, RJ45 conn, 63V AC / 100V DC, 1.5A,10kHz – 80MHz
|
CDN AF2-10kHz
|
CDN for 2 unscreened unbalanced lines, banana conn, 63V AC / 100V DC, 1.5A, 10kHz – 80MHz
|
CDN AF3-10kHz
|
CDN for 3 unscreened unbalanced lines, banana conn, 63V AC / 100V DC, 1.5A, 10kHz – 80MHz
|
CDN AF4-10kHz
|
CDN for 4 unscreened unbalanced lines, banana conn, 63V AC / 100V DC, 1.5A, 10kHz – 80MHz
|
CDN AF6-10kHz
|
CDN for 6 unscreened unbalanced lines, banana conn, 63V AC / 100V DC, 1.5A, 10kHz – 80MHz
|
CDN AF8-10kHz
|
CDN for 8 unscreened unbalanced lines, banana conn, 63V AC / 100V DC, 1.5A, 10kHz – 80MHz
|
|
|
Calibration or short adapters for CDN
|
CWS-CAL
|
Basic calibration kit including 1ea R-100N, 1ea 50cm BNC cable, plastic case
|
R-100N
|
Adapter 150-to-50 Ohm for CDN including aluminium angle
|
CA M1
|
Calibration adapter for all CDN M1 models, EUT port and AE port
|
CA M2/M3/AF3(N)
|
Calibration adapter for CDN M2-32A (AE port only), M3, M3-32A (EUT port and AE port), CDN M2/M3 (EUT port only) and CDN AF3 (EUT port and AE port)
|
CAA M2/M3N
|
Cal kit for CDN M2/M3, CDN M2 and CDN M3 (AE-port only) incl. 1ea Adapter IEC 60320, 1ea R-100N, 1ea T-50
|
CA T2/AF2/M2N
|
Calibration adapter for CDN T2, AF2 (EUT port and AE port) and M2 and M2-32A (EUT port only)
|
CA M2/50-100
|
Calibration adapter for CDN M2-50A, M2-75A and M2-100A (EUT port and AE port)
|
CA M3/50-100
|
Calibration adapter for CDN M3-50A, M3-75A and M3-100A (EUT port and AE port)
|
CA T4/AF4/M4
|
Calibration adapter for CDN T4 and CDN AF4 (EUT port and AE port), CDN M4 and CDN M4-32A (AE port)
|
CA M4N
|
Calibration adapter for CDN M4 N and CDN M4 PE (EUT port)
|
CA M4/50-100
|
Calibration adapter for CDN M4-50A, M4-75A and M4-100A (EUT port and AE port)
|
CA AF5/M5
|
Calibration adapter for CDN AF5 (EUT port and AE port) and CDN M5 (AE port), M5-32A (AE port) and former CDN M5(16A) (EUT port and AE port)
|
CA M5N
|
Calibration adapter for CDN M5 and M5-32A (EUT port)
|
CA M5/50-100
|
Calibration adapter for CDN M5-50A, M5-75A and M5-100A (EUT port and AE port)
|
CA T8RJ45
|
Calibration adapter for CDN T8RJ45 (EUT port and AE port)
|
CA AF8
|
Calibration adapter for CDN AF8 and T8-3A (EUT port and AE port)
|
CA AF10
|
Calibration adapter for CDN AF10 (EUT port and AE port)
|
CA S1
|
Calibration adapter for CDN S1
|
CA S2/S4
|
Calibration adapter for CDN S2 BNC and CDN S4 BNC
|
CA S4-USB
|
Calibration adapter for CDN S4-USB
|
CA S8-RJ45
|
Calibration adapter for CDN S8RJ45
|
CA S9/S15/S25
|
Calibration adapter for CDN S9, CDN S15 and CDN S25
|
CA S37
|
Calibration adapter for CDN S37
|
Remark:
|
For CDN S-Type only one calibration adapter is required, for all other types the standard recommends to also terminate the AE port. One piece of calibration adapter is automatically included in the delivery of every Luethi CDN
|
CA EM
|
Cal kit. for EM 101 incl. 1ea R-100N, 1ea T-50, 1ea connection cable (requires CWS CAL or additional R-100N) See also «Cable EM/FTC 101» as additional option.
|
Cable EM/FTC 101
|
Cable with a length of 1750mm to calibrate an EM 101 together with a FTC 101 (Additional option for item CA EM)
|
|
Decoupling clamps and absorbing clamps to measure disturbance power
|
MDS 21 B
|
Absorbing clamp 30 – 1000MHz as per CISPR 16 for automatic operation, including 5m measuring cable, N-connector
|
FTC 40X15 E
|
Decoupling clamp, 1 – 1000MHz as per CISPR 16 or CISPR 22
|
MDS 22
|
Absorbing clamp 300MHz – 2.5GHz (3GHz) as per CISPR 16
|
EM 101
|
RF Injection clamp, (10kHz) 150kHz – 1000MHz, 100W, 4 kV, max. cable diameter 22mm as per IEC 61000-4-6.
|
FTC 101
|
Decoupling clamp for EM 101 RF injection clamp
|
|
|
Dummy Lamps according to CISPR 15 EN55015
|
LN G23
|
Socket LN G23 according to figure 4 e CISPR 15, socket length 47 mm, tube sets of the RS G23 / xxx series required.
|
RS G23 / 85
|
Tube set for LN G23, max. length of lamp according to IEC 85 mm, length of tube 38 mm, Tube diameter 13 mm, 5 W.
|
RS G23 / 115
|
Tube set for LN G23, max. length of lamp according to IEC 115 mm, length of tube 68 mm, Tube diameter 13 mm, 7 W.
|
RS G23 / 145
|
Tube set for LN G23, max. length of lamp according to IEC 145 mm, length of tube 98 mm, Tube diameter 13 mm, 9 W.
|
RS G23 / 215
|
Tube set for LN G23, max. length of lamp according to IEC 215 mm, length of tube 168 mm, Tube diameter 13 mm, 11 W.
|
|
|
single capped quadruple tube dummy lamps with socket G24
|
LN G24
|
Socket LN G24 according to figure 4 f CISPR 15, socket length 45 mm, tube sets of the RS G24 / xxx series required.
|
RS G24 / 95
|
Tube set for LN G24, max. length of lamp according to IEC 95 mm, length of tube 50 mm, Tube diameter 13 mm, 10 W.
|
RS G24 / 130
|
Tube set for LN G24, max. length of lamp according to IEC 130 mm, length of tube 85 mm, Tube diameter 13 mm, 13 W.
|
RS G24 / 150
|
Tube set for LN G24, max. length of lamp according to IEC 150 mm, length of tube 105 mm, Tube diameter 13 mm, 18 W.
|
RS G24 / 170
|
Tube set for LN G24, max. length of lamp according to IEC 170 mm, length of tube 125 mm, Tube diameter 13 mm, 26 W.
|
|
|
single capped twin tube dummy lamps with socket 2G11
|
LN 2G11
|
Socket LN 2G11 according to figure 4 d CISPR 15, socket length 67 mm, tube sets of the RS 2G11 / xxx series required.
|
RS 2G11 / 225
|
Tube set for LN 2G11, max. length of lamp according to IEC 225 mm, length of tube 158 mm, Tube diameter 15 mm, 18 W.
|
RS 2G11 / 320
|
Tube set for LN 2G11, max. length of lamp according to IEC 320 mm, length of tube 253 mm, Tube diameter 15 mm, 24 W.
|
RS 2G11 / 415
|
Tube set for LN 2G11, max. length of lamp according to IEC 415 mm, length of tube 348 mm, Tube diameter 15 mm, 36 W.
|
RS 2G11 / 535
|
Tube set for LN 2G11, max. length of lamp according to IEC 535 mm, length of tube 468 mm, Tube diameter 15 mm, 55 W.
|
|
|
Linear dummy lamps 15 mm diameter with socket G5
|
LN G5
|
Pair of sockets LN G5 according to figure 4 c CISPR 15, socket length 20 mm each, tube sets of the RS G5 / xxx series required.
|
RS G5 / 136
|
Tube set for LN G5, max. length of lamp according to IEC 136 mm, length of tube 96 mm, Tube diameter 15 mm, 4 W.
|
RS G5 / 212
|
Tube set for LN G5, max. length of lamp according to IEC 212 mm, length of tube 172 mm, Tube diameter 15 mm, 6 W.
|
RS G5 / 288
|
Tube set for LN G5, max. length of lamp according to IEC 288 mm, length of tube 248 mm, Tube diameter 15 mm, 8 W.
|
RS G5 / 517
|
Tube set for LN G5, max. length of lamp according to IEC 517 mm, length of tube 477 mm, Tube diameter 15 mm, 13 W.
|
RS G5 / 549
|
Tube set for LN G5, max. length of lamp according to IEC 549 mm, length of tube 509 mm, Tube diameter 15 mm, 14 W.
|
RS G5 / 849
|
Tube set for LN G5, max. length of lamp according to IEC 849 mm, length of tube 809 mm, Tube diameter 15 mm, 21 W.
|
RS G5 / 1449
|
Tube set for LN G5, max. length of lamp according to IEC 1449 mm, length of tube 1409 mm, Tube diameter 15 mm, 35 W.
|
|
|
Linear dummy lamps 20 mm diameter with socket G13 / 25
|
LN G13 / 25
|
Pair of sockets LN G13 according to figure 4 a CISPR 15, socket length 75 mm each, tube sets of the RS G13 / 25 / xxx series required.
|
RS G13 / 25 / 438
|
Tube set for LN G13 / 25, max. length of lamp according to IEC 438 mm, length of tube 288 mm, Tube diameter 20 mm, 15 W.
|
RS G13 / 25 / 590
|
Tube set for LN G13 / 25, max. length of lamp according to IEC 590 mm, length of tube 440 mm, Tube diameter 20 mm, 18 W.
|
RS G13 / 25 / 720
|
Tube set for LN G13 / 25, max. length of lamp according to IEC 720 mm, length of tube 570 mm, Tube diameter 20 mm, 16 W.
|
RS G13 / 25 / 895
|
Tube set for LN G13 / 25, max. length of lamp according to IEC 895 mm, length of tube 745 mm, Tube diameter 20 mm, 30 W.
|
RS G13 / 25 / 970
|
Tube set for LN G13 / 25, max. length of lamp according to IEC 970 mm, length of tube 820 mm, Tube diameter 20 mm, 36 W.
|
RS G13 / 25 / 1047
|
Tube set for LN G13 / 25, max. length of lamp according to IEC 1047 mm, length of tube 897 mm, Tube diameter 20 mm, 38 W.
|
RS G13 / 25 / 1200
|
Tube set for LN G13 / 25, max. length of lamp according to IEC 1200 mm, length of tube 1050 mm, Tube diameter 20 mm, 36 W.
|
RS G13 / 25 / 1500
|
Tube set for LN G13 / 25, max. length of lamp according to IEC 1500 mm, length of tube 1350 mm, Tube diameter 20 mm, 58 W.
|
|
|
Linear dummy lamps 28 mm diameter with socket G13 / 38
|
LN G13 / 38
|
Pair of sockets LN G13 according to figure 4 a CISPR 15, socket length 75 mm each, tube sets of the RS G13 / 38 / xxx series required.
|
RS G13 / 38 / 590
|
Tube set for LN G13 / 38, max. length of lamp according to IEC 590 mm, length of tube 440 mm, Tube diameter 28 mm, 20 W.
|
RS G13 / 38 / 970
|
Tube set for LN G13 / 38, max. length of lamp according to IEC 970 mm, length of tube 820 mm, Tube diameter 28 mm, 25 W.
|
RS G13 / 38 / 1200
|
Tube set for LN G13 / 38, max. length of lamp according to IEC 1200 mm, length of tube 1050 mm, Tube diameter 28 mm, 115 W.
|
RS G13 / 38 / 1500
|
Tube set for LN G13 / 38, max. length of lamp according to IEC 1500 mm, length of tube 1350 mm, Tube diameter 28 mm, 140 W.
|
RS G13 / 38 / 1800
|
Tube set for LN G13 / 38, max. length of lamp according to IEC 1800 mm, length of tube 1650 mm, Tube diameter 28 mm, 160 W.
|
RS G13 / 38 / 2400
|
Tube set for LN G13 / 38, max. length of lamp according to IEC 2400 mm, length of tube 2250 mm, Tube diameter 28 mm, 125 W.
|
|
|
single capped twin tube dummy lamps with socket 2G7
|
LN 2G7
|
Socket LN 2G7, socket length 47 mm, tube sets of the RS 2G7 / xxx series required.
|
RS 2G7 / 85
|
Tube set for LN 2G7, max. length of lamp according to IEC 85 mm, length of tube 38 mm, Tube diameter 13 mm, 5 W.
|
RS 2G7 / 115
|
Tube set for LN 2G7, max. length of lamp according to IEC 115 mm, length of tube 68 mm, Tube diameter 13 mm, 7 W.
|
RS 2G7 / 145
|
Tube set for LN 2G7, max. length of lamp according to IEC 145 mm, length of tube 98 mm, Tube diameter 13 mm, 9 W.
|
RS 2G7 / 215
|
Tube set for LN 2G7, max. length of lamp according to IEC 215 mm, length of tube 168 mm, Tube diameter 13 mm, 11 W.
|
|
|
U-shape tube dummy lamps with socket 2G13
|
LN 2G13
|
Socket LN 2G13, socket length 75 mm, tube sets of the RS 2G13 / xxx series required.
|
RS 2G13 / 310
|
Tube set for LN 2G13, max. length of lamp according to IEC 310 mm, length of tube 235 mm, Tube diameter 20 mm, 20 W.
|
RS 2G13 / 607
|
Tube set for LN 2G13, max. length of lamp according to IEC 607 mm, length of tube 532 mm, Tube diameter 20 mm, 40 W.
|
RS 2G13 / 765
|
Tube set for LN 2G13, max. length of lamp according to IEC 765 mm, length of tube 690 mm, Tube diameter 20 mm, 65 W.
|
|
Circular dummy lamps
|
LN G10q / 28 / 216
|
Complete circular dummy lamp according to figure 4 b CISPR 15, max. diameter of lamp according to IEC 216 mm, Tube diameter 20 mm, 22 W.
|
LN G10q / 32 / 311
|
Complete circular dummy lamp according to figure 4 b CISPR 15, max. diameter of lamp according to IEC 311 mm, Tube diameter 28 mm, 32 W.
|
LN G10q / 32 / 413
|
Complete circular dummy lamp according to figure 4 b CISPR 15, max. diameter of lamp according to IEC 413 mm, Tube diameter 28 mm, 40 W.
|
|
|
single pin linear dummy lamps with socket Fa6
|
LN Fa6
|
Pair of sockets LN Fa6, socket length 75 mm each, tube sets of the RS Fa6 / xxx series required.
|
RS Fa6 / 590
|
Tube set for LN Fa6, max. length of lamp according to IEC 590 mm, length of tube 440 mm, Tube diameter 28 mm, 16 W.
|
RS Fa6 / 1200
|
Tube set for LN Fa6, max. length of lamp according to IEC 1200 mm, length of tube 1050 mm, Tube diameter 28 mm, 32 W.
|
RS Fa6 / 1500
|
Tube set for LN Fa6, max. length of lamp according to IEC 1500 mm, length of tube 1350 mm, Tube diameter 28 mm, 50 W.
|
|
|
related equipment
|
Conical cover
|
Test fixture for energy saving lamps with E27 socket according to figure 7 b CISPR 15
|
Conical Cover Option E14
|
Additional adapter E27-E14 to insert E14 lamps into the conical cover.
|
Conical Cover Option B22d
|
Additional adapter E27-B22d to insert B22d lamps (common in Great Britain) into the conical cover.
|
